CAD CAM EDM DRO - Yahoo Group Archive

Re: Reed switch for limits - anyone done it?

Posted by mszollar
on 2002-08-17 12:44:52 UTC
I'd like to thank all that responded, the good news (in my case) is
near 100% of that I mill is Delrin and Aluminum; neither of which
has much magnetic properties. I was planing to place the switches
against travel to shorten the contact time with the magnetic field
(it should also increase accuracy). I'd love to use hall effect but
there is a bit more electronics needed and for a Sherline that may
be overkill (but it would be more accurate).

At the same time I was considering optical (using laser LED and
detector). Very accurate but need mouting is a challenge and the
additional electronics as well. There is the cost and its only a
Sherline.

I'll let all know what I end up with and how accurate the final
product end up being.

Thanks again

Discussion Thread

mszollar 2002-08-14 22:26:35 UTC Reed switch for limits - anyone done it? Peter Homann 2002-08-14 22:46:54 UTC RE: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Ian W. Wright 2002-08-15 00:48:47 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? JJ 2002-08-15 05:45:03 UTC RE: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Carol & Jerry Jankura 2002-08-15 06:09:43 UTC RE: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? JanRwl@A... 2002-08-15 07:59:48 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Alan Marconett KM6VV 2002-08-15 10:27:42 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Matt Shaver 2002-08-15 18:26:37 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Alan Marconett KM6VV 2002-08-15 18:36:50 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Carol & Jerry Jankura 2002-08-15 20:54:59 UTC RE: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Matt Shaver 2002-08-15 21:20:18 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Alan Marconett KM6VV 2002-08-16 09:44:39 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Jon Elson 2002-08-16 10:18:18 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Alan Marconett KM6VV 2002-08-16 12:51:13 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Dave Engvall 2002-08-17 08:16:15 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? Jon Anderson 2002-08-17 08:41:25 UTC Re: [CAD_CAM_EDM_DRO] Reed switch for limits - anyone done it? mszollar 2002-08-17 12:44:52 UTC Re: Reed switch for limits - anyone done it? Bill Vance 2002-08-17 15:44:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Reed switch for limits - anyone done it? turbulatordude 2002-08-17 20:10:00 UTC Re: Reed switch for limits - anyone done it?