CAD CAM EDM DRO - Yahoo Group Archive

Re: It's ALIVE!!!

Posted by barclaygeo
on 2002-11-29 20:21:33 UTC
Ooops, I mean 24volt and 1.2Amp

Barclay

--- In CAD_CAM_EDM_DRO@y..., "barclaygeo" <bdog4@h...> wrote:
> I'm using 6v motors at 24v and I think I'm at 10A. I need to look
> into the current reduction.
>
> Thanks,
>
> Barclay
>
> --- In CAD_CAM_EDM_DRO@y..., "Tim Goldstein" <timg@k...> wrote:
> > If you have near recent Gecko G2xx drives you would have idle
> current
> > reduction. That should keep the motors from getting very hot at
all
> when
> > they are idling. You did not mention what voltage you are using
or
> the
> > current you are set for. If the voltage is pushing up towards 25X
> over
> > voltage or your current is set too high you will get lots of heat.
> >
> > Tim
> > [Denver CO]
> > Sherline Products at Deep Discount
> > Mach1 & DeskCNC with Credit Card ordering
> > Ask about Sherline and DeskCNC bundle discounts
> > www.KTMarketing.com/Sherline
> >
> > > -----Original Message-----
> > > I finally got everything straight in Mach1 and my setup is now
> > > functioning. Now just need to figure out my settings for my
> motor.
> > > More research.
> > >
> > > Are the motors supposed to be getting hot setting idle. Mine
> feel
> > > very hot.
> > >
> > > Thanks,
> > >
> > > Barclay
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html

Discussion Thread

barclaygeo 2002-11-29 18:54:55 UTC It's ALIVE!!! Tim Goldstein 2002-11-29 19:54:32 UTC RE: [CAD_CAM_EDM_DRO] It's ALIVE!!! barclaygeo 2002-11-29 20:20:13 UTC Re: It's ALIVE!!! barclaygeo 2002-11-29 20:21:33 UTC Re: It's ALIVE!!! Tim Goldstein 2002-11-29 20:26:51 UTC RE: [CAD_CAM_EDM_DRO] Re: It's ALIVE!!! Dan Mauch 2002-11-30 08:07:40 UTC RE: [CAD_CAM_EDM_DRO] It's ALIVE!!! George Erhart 2002-11-30 14:12:27 UTC Re: [CAD_CAM_EDM_DRO] It's ALIVE!!! Tim Goldstein 2002-11-30 14:23:42 UTC RE: [CAD_CAM_EDM_DRO] It's ALIVE!!! Fusion X Studio 2002-11-30 16:07:57 UTC Re: [CAD_CAM_EDM_DRO] Re: It's ALIVE!!! Dan Mauch 2002-12-01 08:19:00 UTC The ultimate shop PC sytem JanRwl@A... 2002-12-01 19:31:08 UTC Re: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem Dan Mauch 2002-12-02 06:28:33 UTC RE: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem CL 2002-12-02 13:25:42 UTC Re: [CAD_CAM_EDM_DRO] Mach1 -> Fully released. (Finally) JanRwl@A... 2002-12-02 14:33:12 UTC Re: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem Askew, Jason 2002-12-02 14:37:50 UTC RE: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem Marv Frankel 2002-12-02 15:04:41 UTC Re: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem n4onl 2002-12-02 15:31:01 UTC Re: The ultimate shop PC sytem Art 2002-12-02 16:49:39 UTC Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem JanRwl@A... 2002-12-02 17:28:31 UTC Re: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem JanRwl@A... 2002-12-02 17:53:01 UTC Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem Paul Amaranth 2002-12-02 18:46:46 UTC Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem Carol & Jerry Jankura 2002-12-02 19:24:48 UTC RE: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem echnidna 2002-12-02 19:38:42 UTC Re: The ultimate shop PC sytem Marv Frankel 2002-12-02 19:56:41 UTC Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem JanRwl@A... 2002-12-02 22:28:53 UTC Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem JanRwl@A... 2002-12-02 22:30:49 UTC Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem JanRwl@A... 2002-12-02 22:34:03 UTC Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem Dan Mauch 2002-12-03 06:27:11 UTC RE: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem dserratt2001 <dserratt@n... 2002-12-09 07:45:05 UTC Re: The ultimate shop PC sytem Dan Mauch 2002-12-09 09:05:35 UTC RE: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem