RE: [CAD_CAM_EDM_DRO] It's ALIVE!!!
Posted by
Dan Mauch
on 2002-11-30 08:07:40 UTC
Another very common mistake is that the per phase amperage rating for a
common 6 wire motor is for the unipolar wiring configuration. However
most guys are using bipolar choppers set in the bipolar series
configuration so you should set the current for 71.5% of the rated
current. Thus a 6 wire motor that was rated at 2Amp when used with a
bipolar chopper driver in series wiring should be set for 2A X .715 =
1.43 amps.
Dan
-----Original Message-----
From: Tim Goldstein [mailto:timg@...]
Sent: Friday, November 29, 2002 7:54 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: RE: [CAD_CAM_EDM_DRO] It's ALIVE!!!
If you have near recent Gecko G2xx drives you would have idle current
reduction. That should keep the motors from getting very hot at all when
they are idling. You did not mention what voltage you are using or the
current you are set for. If the voltage is pushing up towards 25X over
voltage or your current is set too high you will get lots of heat.
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
common 6 wire motor is for the unipolar wiring configuration. However
most guys are using bipolar choppers set in the bipolar series
configuration so you should set the current for 71.5% of the rated
current. Thus a 6 wire motor that was rated at 2Amp when used with a
bipolar chopper driver in series wiring should be set for 2A X .715 =
1.43 amps.
Dan
-----Original Message-----
From: Tim Goldstein [mailto:timg@...]
Sent: Friday, November 29, 2002 7:54 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: RE: [CAD_CAM_EDM_DRO] It's ALIVE!!!
If you have near recent Gecko G2xx drives you would have idle current
reduction. That should keep the motors from getting very hot at all when
they are idling. You did not mention what voltage you are using or the
current you are set for. If the voltage is pushing up towards 25X over
voltage or your current is set too high you will get lots of heat.
> -----Original Message-----Addresses:
> I finally got everything straight in Mach1 and my setup is now
> functioning. Now just need to figure out my settings for my motor.
> More research.
>
> Are the motors supposed to be getting hot setting idle. Mine feel
> very hot.
>
> Thanks,
>
> Barclay
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
Discussion Thread
barclaygeo
2002-11-29 18:54:55 UTC
It's ALIVE!!!
Tim Goldstein
2002-11-29 19:54:32 UTC
RE: [CAD_CAM_EDM_DRO] It's ALIVE!!!
barclaygeo
2002-11-29 20:20:13 UTC
Re: It's ALIVE!!!
barclaygeo
2002-11-29 20:21:33 UTC
Re: It's ALIVE!!!
Tim Goldstein
2002-11-29 20:26:51 UTC
RE: [CAD_CAM_EDM_DRO] Re: It's ALIVE!!!
Dan Mauch
2002-11-30 08:07:40 UTC
RE: [CAD_CAM_EDM_DRO] It's ALIVE!!!
George Erhart
2002-11-30 14:12:27 UTC
Re: [CAD_CAM_EDM_DRO] It's ALIVE!!!
Tim Goldstein
2002-11-30 14:23:42 UTC
RE: [CAD_CAM_EDM_DRO] It's ALIVE!!!
Fusion X Studio
2002-11-30 16:07:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: It's ALIVE!!!
Dan Mauch
2002-12-01 08:19:00 UTC
The ultimate shop PC sytem
JanRwl@A...
2002-12-01 19:31:08 UTC
Re: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem
Dan Mauch
2002-12-02 06:28:33 UTC
RE: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem
CL
2002-12-02 13:25:42 UTC
Re: [CAD_CAM_EDM_DRO] Mach1 -> Fully released. (Finally)
JanRwl@A...
2002-12-02 14:33:12 UTC
Re: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem
Askew, Jason
2002-12-02 14:37:50 UTC
RE: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem
Marv Frankel
2002-12-02 15:04:41 UTC
Re: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem
n4onl
2002-12-02 15:31:01 UTC
Re: The ultimate shop PC sytem
Art
2002-12-02 16:49:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem
JanRwl@A...
2002-12-02 17:28:31 UTC
Re: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem
JanRwl@A...
2002-12-02 17:53:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem
Paul Amaranth
2002-12-02 18:46:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem
Carol & Jerry Jankura
2002-12-02 19:24:48 UTC
RE: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem
echnidna
2002-12-02 19:38:42 UTC
Re: The ultimate shop PC sytem
Marv Frankel
2002-12-02 19:56:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem
JanRwl@A...
2002-12-02 22:28:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem
JanRwl@A...
2002-12-02 22:30:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem
JanRwl@A...
2002-12-02 22:34:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem
Dan Mauch
2002-12-03 06:27:11 UTC
RE: [CAD_CAM_EDM_DRO] The ultimate shop PC sytem
dserratt2001 <dserratt@n...
2002-12-09 07:45:05 UTC
Re: The ultimate shop PC sytem
Dan Mauch
2002-12-09 09:05:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: The ultimate shop PC sytem