making DRO boards (was Re: Card, kit or schematic for Kuluga/Mauch DRO card
Posted by
turbulatordude <davemucha@j...
on 2003-01-03 11:14:41 UTC
Hi Guys,
a little reviewing and it seems that this project uses the internal
slot for the ISA connection in a standard PC.
Although I am pretty sure you can adapt it to a PCI bus, it is laid
out around a ISA bus.
The problem with getting cards made is that this would be a press in
card into the PC motherboard. that means cutting a section to insert
into the slot.
since the circuit is so simple, I would propose 2 methods to get it
done.
#1, buy a prototype board from Jameco P/N 21531 or something
similar. then stuffing it and using jumper wires for connections.
These are going for a $22.95 plus shipping.
#2, cut out a NIC or other ISA card, have a small board made and then
bolt that onto the salvage board and jumper that board into the
correct pins.
and here is a link from another similar project.
http://www.boondog.com/%5Ctutorials%5C7266%5C7266.htm
my $0.02 worth.
Dave
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "j.guenther"
<j.guenther@v...> wrote:
a little reviewing and it seems that this project uses the internal
slot for the ISA connection in a standard PC.
Although I am pretty sure you can adapt it to a PCI bus, it is laid
out around a ISA bus.
The problem with getting cards made is that this would be a press in
card into the PC motherboard. that means cutting a section to insert
into the slot.
since the circuit is so simple, I would propose 2 methods to get it
done.
#1, buy a prototype board from Jameco P/N 21531 or something
similar. then stuffing it and using jumper wires for connections.
These are going for a $22.95 plus shipping.
#2, cut out a NIC or other ISA card, have a small board made and then
bolt that onto the salvage board and jumper that board into the
correct pins.
and here is a link from another similar project.
http://www.boondog.com/%5Ctutorials%5C7266%5C7266.htm
my $0.02 worth.
Dave
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "j.guenther"
<j.guenther@v...> wrote:
> Thanks Tim,be missing
>
> I just got the latest stuff from your site, and all that seems to
> (unless I just missed it) is the schematic for the 4 axis card. Iwill be
> checking with a couple of the PC board houses listed in CircuitCellar to
> get a cost on getting the boards made. I will check with DanMauch, off
> line, to see if it is permissible to get a few boards made forothers on the
> list.the
>
> Many thanks to you and Dan for making this information available to
> group.Kuluga/Mauch
>
> John Guenther
> 'Ye Olde Pen Maker'
> Sterling, Virginia
>
> > -----Original Message-----
> > From: Tim Goldstein [mailto:timg@k...]
> > Sent: Friday, January 03, 2003 12:58 PM
> > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subject: Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for
> > DRO card wantedCCED list.
> >
> >
> > John,
> >
> > The only difference is an additional LS-7266. All other chips are
> > the same.
> >
> > Tim
> > [Denver, CO]
> > Sherline products at Deep Discount
> > Mach1 & DeskCNC with Credit Card ordering
> > www.KTMarketing.com/Sherline
> > www.KTMarketing.com/DeskCNC
> >
> >
> > ----- Original Message -----
> > > Tim,
> > >
> > > Thanks, I got the stuff from you site but what I really want is
> > the 4 axis
> > > card.
> > >
> > > John Guenther
> > > 'Ye Olde Pen Maker'
> > > Sterling, Virginia
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@a...
> > Moderator: jmelson@a... timg@k... [Moderator]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
> > to be a sister site to the CCED group, as many of the same
> > members are there, for OT subjects, that are not allowed on the
> >http://docs.yahoo.com/info/terms/
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> > POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> > EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
> >
> >
> >
Discussion Thread
John Guenther
2003-01-02 19:38:56 UTC
Card, kit or schematic for Kuluga/Mauch DRO card wanted
Vince Negrete
2003-01-03 01:38:37 UTC
Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
kdoney_63021 <kdoney_63021@y...
2003-01-03 01:38:50 UTC
Re: Card, kit or schematic for Kuluga/Mauch DRO card wanted
Tim Goldstein
2003-01-03 01:39:53 UTC
RE: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
John Guenther
2003-01-03 05:24:46 UTC
RE: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
John Guenther
2003-01-03 05:24:48 UTC
RE: [CAD_CAM_EDM_DRO] Re: Card, kit or schematic for Kuluga/Mauch DRO card wanted
Dan Mauch
2003-01-03 06:49:15 UTC
RE: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
j.guenther
2003-01-03 07:42:49 UTC
RE: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
Dan Mauch
2003-01-03 08:02:24 UTC
RE: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
turbulatordude <davemucha@j...
2003-01-03 08:04:23 UTC
Re: Card, kit or schematic for Kuluga/Mauch DRO card wanted
Vince Negrete
2003-01-03 08:05:36 UTC
Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
alex
2003-01-03 08:13:21 UTC
Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
Dan Mauch
2003-01-03 09:34:05 UTC
RE: [CAD_CAM_EDM_DRO] Re: Card, kit or schematic for Kuluga/Mauch DRO card wanted
Tim Goldstein
2003-01-03 09:57:47 UTC
Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
j.guenther
2003-01-03 10:23:39 UTC
RE: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
alex
2003-01-03 10:39:42 UTC
Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
Alan Marconett KM6VV
2003-01-03 10:46:52 UTC
Re: Card, kit or schematic for Kuluga/Mauch DRO card wanted
turbulatordude <davemucha@j...
2003-01-03 11:14:41 UTC
making DRO boards (was Re: Card, kit or schematic for Kuluga/Mauch DRO card
C.S. Mo
2003-01-03 11:18:29 UTC
Re: [CAD_CAM_EDM_DRO] making DRO boards (was Re: Card, kit or schematic for Kuluga/Mauch DRO card
Carl Mikkelsen, Oasis
2003-01-03 11:36:05 UTC
Re: [CAD_CAM_EDM_DRO] making DRO boards (was Re: Card, kit or schematic for Kuluga/Mauch DRO card
alex
2003-01-03 11:54:48 UTC
Re: [CAD_CAM_EDM_DRO] making DRO boards (was Re: Card, kit or schematic for Kuluga/Mauch DRO card
Vince Negrete
2003-01-03 15:28:13 UTC
Card, kit or schematic for Kuluga/Mauch DRO card wanted
Hans Wedemeyer
2003-01-03 16:10:49 UTC
Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
Dan Mauch
2003-01-03 18:47:18 UTC
RE: [CAD_CAM_EDM_DRO] making DRO boards (was Re: Card, kit orschematic for Kuluga/Mauch DRO card
Dan Mauch
2003-01-03 19:18:53 UTC
RE: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
Hans Wedemeyer
2003-01-03 19:21:29 UTC
Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
Jon Elson
2003-01-03 22:22:03 UTC
Re: [CAD_CAM_EDM_DRO] making DRO boards (was Re: Card, kit or schematic for Kuluga/Mauch DRO card
James Owens
2003-01-05 18:11:33 UTC
Re: [CAD_CAM_EDM_DRO] Card, kit or schematic for Kuluga/Mauch DRO card wanted
george_barr
2003-05-24 01:03:56 UTC
Re: Card, kit or schematic for Kuluga/Mauch DRO card wanted