Re: loose quil
Posted by
turbulatordude <davemucha@j...
on 2003-01-20 09:30:48 UTC
Interesting idea.
seems the thin gap, less than 2 mil makes it hard to get the stuff in
there. With a thin gap, I cannot see how to fill the void
Also it would seem that any type of epoxy or other plastics would
provide a slipery surface and fill the gap. Since there is no
pressure on the material and no grit it should have a long service
life.
Coating the quill before filling is important too.
so,it seems like I would wind up with a smooth bore or solid part.....
any ideas on how to inject the stuff evenly ? sounds like a grouve
would allow for the material to be carried around the quill, and then
just pressurize until it comes out along the circumference.
Dave
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "vrsculptor
<vrsculptor@h...>" <vrsculptor@h...> wrote:
seems the thin gap, less than 2 mil makes it hard to get the stuff in
there. With a thin gap, I cannot see how to fill the void
Also it would seem that any type of epoxy or other plastics would
provide a slipery surface and fill the gap. Since there is no
pressure on the material and no grit it should have a long service
life.
Coating the quill before filling is important too.
so,it seems like I would wind up with a smooth bore or solid part.....
any ideas on how to inject the stuff evenly ? sounds like a grouve
would allow for the material to be carried around the quill, and then
just pressurize until it comes out along the circumference.
Dave
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "vrsculptor
<vrsculptor@h...>" <vrsculptor@h...> wrote:
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, JanRwl@A... wrote:
> > In a message dated 1/19/2003 6:19:23 PM Central Standard Time,
> > david_mucha@y... writes:
> >
> >
> > > I thouhgt about chrome/nickle plating or some sort of
> > > electroplating. I am also considdering just using some shim
> stock.
> > >
> > > The frame is cast iron and the quill is steel.
> > >
> > > any ideas ?
> >
> Dave,
> How about one of the castable (is that a word?) plastic bearing
> materials like turcite?
>
> Roger S
Discussion Thread
david_mucha <david_mucha@y...
2003-01-19 16:17:46 UTC
loose quil
JanRwl@A...
2003-01-19 16:39:17 UTC
Re: [CAD_CAM_EDM_DRO] loose quil
Marv Frankel
2003-01-19 17:12:16 UTC
Re: [CAD_CAM_EDM_DRO] loose quil
Tim Goldstein
2003-01-19 17:57:46 UTC
List management personnel changes
wanliker@a...
2003-01-19 18:16:59 UTC
Re: [CAD_CAM_EDM_DRO] List management personnel changes
Dan Mauch
2003-01-20 07:12:16 UTC
RE: [CAD_CAM_EDM_DRO] loose quil
vrsculptor <vrsculptor@h...
2003-01-20 07:44:16 UTC
Re: loose quil
doug98105 <dougrasmussen@c...
2003-01-20 07:47:50 UTC
Re: loose quil
turbulatordude <davemucha@j...
2003-01-20 09:30:48 UTC
Re: loose quil
Marv Frankel
2003-01-20 11:03:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: loose quil
Jon Anderson
2003-01-20 11:17:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: loose quil
turbulatordude <davemucha@j...
2003-01-20 11:23:16 UTC
Re: loose quil
ballendo <ballendo@y...
2003-01-23 01:10:48 UTC
Re: loose quill
turbulatordude <davemucha@j...
2003-01-23 06:24:31 UTC
Re: loose quill