Re: CMD-260 test mode?
Posted by
echnidna <echnidna@y...
on 2003-02-19 00:27:33 UTC
I get an impression you have assumed that all nema 42's are 2.1 volts
and 9 amps, if so you are incorrect, they come with varying voltage
and current ratings
My router has a nema 42 of 3.6 volts and 6.1 amps.
A few weeks ago on ebay there were a couple of nema 42's with 4 amp
current ratings.
Some motor plates only give some of the ratings.
If your motor plate only tells you the voltage OR the current, you
need to measure the resistance with a digital multimeter and use that
figure to calculate the missing parameter with the formula
R=E/I
Regards
Bob Thomas
-- In CAD_CAM_EDM_DRO@yahoogroups.com, "Jeff Goldberg" <jeff@w...>
wrote:
and 9 amps, if so you are incorrect, they come with varying voltage
and current ratings
My router has a nema 42 of 3.6 volts and 6.1 amps.
A few weeks ago on ebay there were a couple of nema 42's with 4 amp
current ratings.
Some motor plates only give some of the ratings.
If your motor plate only tells you the voltage OR the current, you
need to measure the resistance with a digital multimeter and use that
figure to calculate the missing parameter with the formula
R=E/I
Regards
Bob Thomas
-- In CAD_CAM_EDM_DRO@yahoogroups.com, "Jeff Goldberg" <jeff@w...>
wrote:
> I believe NEMA 42's have a nominal voltage of 2.1 volts. I've beenwarned
> that if I exceed 25 times the voltage, the motors run too hot.They're
> rated 9 amps so the 8 amp limit of the drive shouldn't present aproblem.
>
Discussion Thread
washcomp <jeff@w...
2003-02-18 13:59:25 UTC
CMD-260 test mode?
stevenson_engineers <machines@n...
2003-02-18 16:46:06 UTC
Re: CMD-260 test mode?
Jeff Goldberg
2003-02-18 17:56:34 UTC
RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode?
Jeff Goldberg
2003-02-18 18:50:33 UTC
RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode?
turbulatordude <davemucha@j...
2003-02-18 19:20:34 UTC
Re: CMD-260 test mode?
Tim Goldstein
2003-02-18 19:59:39 UTC
RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode?
tony@j...
2003-02-18 20:20:56 UTC
Re: CMD-260 test mode?
Tim Goldstein
2003-02-18 21:24:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode?
echnidna <echnidna@y...
2003-02-19 00:27:33 UTC
Re: CMD-260 test mode?
Jeff Goldberg
2003-02-19 05:02:10 UTC
RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode?
turbulatordude <davemucha@j...
2003-02-19 07:37:08 UTC
Re: CMD-260 test mode?
Tim Goldstein
2003-02-19 07:57:22 UTC
RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode?
Alan Marconett KM6VV
2003-02-19 11:42:50 UTC
Re: CMD-260 test mode?
Alan Marconett KM6VV
2003-02-19 11:48:29 UTC
Re: CMD-260 test mode?
turbulatordude <davemucha@j...
2003-02-19 11:58:39 UTC
Re: CMD-260 test mode?