CAD CAM EDM DRO - Yahoo Group Archive

Re: CMD-260 test mode?

on 2003-02-18 16:46:06 UTC
Jeff,
With the combination you have of the 260's and the 42 series motors
you will need all the power you can get.
The 260's are rated for 80 volt at 8 amp and it would be adviseable
to get somewhere near these limits.
With a 50 volt AC supply, by the time it's rectified and smoothed,
you will have 70 volts DC which is close enought to 80 volts but not
too close to cause over voltage problems.

John S.

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "washcomp <jeff@w...>"
<jeff@w...> wrote:
> Well I'm nearly there. I've got a power supply, 3 CMD-260 drives
and
> a Bridgeport with NEMA 42 steppers on the XY and Z axis. I still
> have to get a PC connected and load some software (thinking of MACH
> 1 - pros and cons would be appreciated).
>
> Until I get the PC hooked up, I'd like to test the drive/stepper
> combination. (The motors are unmarked and I'm taking some best
> guesses at an appropriate power supply. I'm going to try 34 volts
at
> 8 amps in parallel and see how hot the motors get. I can still
> change it if things go squrilly). Anyone know if there's a way to
> test them to see if everything works in the absence of the PC,
> software, etc.? Can I test them unloaded or do they have to be
> attached to the Bridgeport?
>
> If not, can a PC be used to test in the absence of CNC software?
>
> Thank for all the help.
>
> Regards,
> Jeff

Discussion Thread

washcomp <jeff@w... 2003-02-18 13:59:25 UTC CMD-260 test mode? stevenson_engineers <machines@n... 2003-02-18 16:46:06 UTC Re: CMD-260 test mode? Jeff Goldberg 2003-02-18 17:56:34 UTC RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode? Jeff Goldberg 2003-02-18 18:50:33 UTC RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode? turbulatordude <davemucha@j... 2003-02-18 19:20:34 UTC Re: CMD-260 test mode? Tim Goldstein 2003-02-18 19:59:39 UTC RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode? tony@j... 2003-02-18 20:20:56 UTC Re: CMD-260 test mode? Tim Goldstein 2003-02-18 21:24:01 UTC RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode? echnidna <echnidna@y... 2003-02-19 00:27:33 UTC Re: CMD-260 test mode? Jeff Goldberg 2003-02-19 05:02:10 UTC RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode? turbulatordude <davemucha@j... 2003-02-19 07:37:08 UTC Re: CMD-260 test mode? Tim Goldstein 2003-02-19 07:57:22 UTC RE: [CAD_CAM_EDM_DRO] Re: CMD-260 test mode? Alan Marconett KM6VV 2003-02-19 11:42:50 UTC Re: CMD-260 test mode? Alan Marconett KM6VV 2003-02-19 11:48:29 UTC Re: CMD-260 test mode? turbulatordude <davemucha@j... 2003-02-19 11:58:39 UTC Re: CMD-260 test mode?