Re: Hot rolled router frame: added note
Posted by
dakota8833 <dakota8833@b...
on 2003-03-02 17:00:01 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "dakota8833 <dakota8833@b...>"
<dakota8833@b...> wrote:
<dakota8833@b...> wrote:
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Leslie M. Watts"---------------------
> <leswatts@a...> wrote:
> > Yes, I think you are on the right track. You could attach pad
> support points
> > to the tubing and then mill just the points flat- averting stress
> induced
> > warpage
> > since you are not machining the tubing itself.
> >
> > I did find the previous message about grouting pads
> > on tubing in my archives so I will include it here with
> > some added comments:
> > ----------------------------------------------
> I used hot rolled on my cnc router, drilled all the holes, weldedof
> everything up and then used epoxy for my rail base. I set a waxed
> precision level into the epoxy. This was done first across the ends
> the two parallels , then down the length of each tube. This gave mea
> +- .001 ready surface for rails. Picts of the manchine are atcncrouter folder.
> http://groups.yahoo.com/group/CAD_CAM_EMC/ Under photos in the
>
> Frank
Discussion Thread
Leslie M. Watts
2003-02-28 11:25:58 UTC
Re: [CAD_CAM_EDM_DRO] Hot rolled router frame: added note
tsalaff <tacman@s...
2003-02-28 14:05:38 UTC
Re: Hot rolled router frame: added note
Leslie M. Watts
2003-02-28 14:34:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
vrsculptor <vrsculptor@h...
2003-02-28 20:00:06 UTC
Re: Hot rolled router frame: added note
Leslie M. Watts
2003-03-01 06:45:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
dakota8833 <dakota8833@b...
2003-03-01 07:18:09 UTC
Re: Hot rolled router frame: added note
Leslie M. Watts
2003-03-01 07:40:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
dakota8833 <dakota8833@b...
2003-03-02 17:00:01 UTC
Re: Hot rolled router frame: added note
turbulatordude <davemucha@j...
2003-03-02 17:22:34 UTC
Re: Hot rolled router frame: added note - EPOXY
dakota8833 <dakota8833@b...
2003-03-02 17:27:47 UTC
Re: Hot rolled router frame: added note
dakota8833 <dakota8833@b...
2003-03-02 19:28:45 UTC
Re: Hot rolled router frame: added note - EPOXY
Miroslav Pejic
2003-03-05 03:51:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
Leslie M. Watts
2003-03-05 05:34:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
ccq@x...
2003-03-05 07:43:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
JanRwl@A...
2003-03-05 12:55:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
Miroslav Pejic
2003-03-05 23:09:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
Miroslav Pejic
2003-03-06 01:10:10 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note
Nigel Bailey
2003-03-06 02:37:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Hot rolled router frame: added note