Re: [CAD_CAM_EDM_DRO] Programmable deviced (was: Setup for stepping on revolution counter)
Posted by
Matt Shaver
on 2003-03-10 12:02:48 UTC
On Monday 10 March 2003 14:03, Carl Mikkelsen wrote:
code come with licensing restrictions that prohibit redistribution of
derivitive works?
Matt
> The Atmel parts are programmed (as well as erased and reprogrammed) throughAny chance you could make this port available to others, or does the Atmel
> a simple 5 volt-only interface. I program them through a parallel
> port. Source code for the programmer is available -- I had to port it to
> Linux, which turned out to be very simple.
code come with licensing restrictions that prohibit redistribution of
derivitive works?
Matt
Discussion Thread
Pablo Roufogalis L.
2003-03-08 17:23:48 UTC
Setup for stepping on revolution counter
Larry Edington
2003-03-08 23:18:18 UTC
Re: [CAD_CAM_EDM_DRO] Setup for stepping on revolution counter
Pablo Roufogalis L.
2003-03-09 05:40:33 UTC
Re: Setup for stepping on revolution counter
Pablo Roufogalis L.
2003-03-09 08:07:10 UTC
Re: Setup for stepping on revolution counter
Nigel Bailey
2003-03-10 02:37:33 UTC
RE: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
alex
2003-03-10 07:19:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
Nigel Bailey
2003-03-10 08:37:45 UTC
RE: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
alex
2003-03-10 08:58:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
JanRwl@A...
2003-03-10 09:28:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
Jon Elson
2003-03-10 10:35:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
Carl Mikkelsen
2003-03-10 11:06:20 UTC
[CAD_CAM_EDM_DRO] Programmable deviced (was: Setup for stepping on revolution counter)
Matt Shaver
2003-03-10 12:02:48 UTC
Re: [CAD_CAM_EDM_DRO] Programmable deviced (was: Setup for stepping on revolution counter)
Carl Mikkelsen
2003-03-10 13:26:19 UTC
Re: [CAD_CAM_EDM_DRO] Programmable deviced (was: Setup for stepping on revolution counter)
Pablo Roufogalis L.
2003-03-10 19:08:28 UTC
Re: Setup for stepping on revolution counter
Nigel Bailey
2003-03-11 03:07:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
alex
2003-03-11 07:40:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
alex
2003-03-11 07:54:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
Nigel Bailey
2003-03-11 08:37:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Setup for stepping on revolution counter
Nigel Bailey
2003-03-13 07:22:11 UTC
re: using optical mouse for DRO / servo feedback
Jon Elson
2003-03-13 09:57:15 UTC
Re: [CAD_CAM_EDM_DRO] re: using optical mouse for DRO / servo feedback
Nigel Bailey
2003-03-14 01:52:06 UTC
RE: [CAD_CAM_EDM_DRO] re: using optical mouse for DRO / servo feedback
Jon Elson
2003-03-14 09:31:10 UTC
Re: [CAD_CAM_EDM_DRO] re: using optical mouse for DRO / servo feedback