Re: Need xyz driver board kit...How do I interface the geckos drivers...
Posted by
Hector
on 2003-06-06 18:01:37 UTC
Hi Bob,
Will the Mach1 control when the router turns on and of If I use a
appropiate software? and does it handle limit switches...I almost
sure it can, so I fill a little dumb asking...
Regards...
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Robert Campbell" <bob@c...>
wrote:
Will the Mach1 control when the router turns on and of If I use a
appropiate software? and does it handle limit switches...I almost
sure it can, so I fill a little dumb asking...
Regards...
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Robert Campbell" <bob@c...>
wrote:
> Hector,my
>
> You may want to look at my web page at www.campbelldesigns.com for
> break-out board.z. So
>
> Bob Campbell
> ----- Original Message -----
> From: "cncnovice" <crcitser@g...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Thursday, June 05, 2003 8:26 PM
> Subject: [CAD_CAM_EDM_DRO] Re: Need xyz driver board kit...How do I
> interface the geckos drivers...
>
>
> > Hector,
> > Contact Robert Campbell on this group. He sells a first-class
> > breakout board that will make it easy to interface your PC to the
> > Geckos and limit switches - very reasonable in cost, too.
> >
> > Good luck,
> > John Champlain
> >
> >
> >
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Hector"
> > <hector_a_quintanilla@y...> wrote:
> > > I need to know which gecko driver can drive te sanyo-DEnki H
> > Series,
> > > teh model I mentioned earlier. And I'm not an expert, I just
> > > starting so If I understand correct the geckos are single axis
> > > controllers, so I will need three, one for each axis x,y,and
> > > with what kind of interface do I send signals to each separatewanliker@a...,
> > > driver? I want to send signals through the parallel port on my
> > > computer, from there to a interface that controls each axis.
> > > Regards..
> > > HEctor Quintanilla
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> timg@k...reach it if
> > Moderator: pentam@c... indigo_red@q... [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> you have trouble.to be a
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
> sister site to the CCED group, as many of the same members arethere, for OT
> subjects, that are not allowed on the CCED list.POSTING THEM.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........http://docs.yahoo.com/info/terms/
> > bill
> > List Mom
> > List Owner
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
> >
Discussion Thread
Hector
2003-06-03 22:41:48 UTC
Need xyz driver board kit...Please advise
Robert Campbell
2003-06-04 07:18:52 UTC
Re: [CAD_CAM_EDM_DRO] Need xyz driver board kit...Please advise
turbulatordude
2003-06-04 07:51:42 UTC
Re: Need xyz driver board kit...Please advise
Hector
2003-06-05 18:30:22 UTC
Re: Need xyz driver board kit...Please advise--This is the motors I'm looking to
Hector
2003-06-05 18:35:54 UTC
Re: Need xyz driver board kit...How do I interface the geckos drivers...
cncnovice
2003-06-05 20:26:42 UTC
Re: Need xyz driver board kit...How do I interface the geckos drivers...
wayne_j_hill
2003-06-05 21:17:20 UTC
Re: Need xyz driver board kit...How do I interface the geckos drivers...
Robert Campbell
2003-06-06 05:34:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need xyz driver board kit...How do I interface the geckos drivers...
Hector
2003-06-06 18:01:37 UTC
Re: Need xyz driver board kit...How do I interface the geckos drivers...
Robert Campbell
2003-06-06 18:41:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need xyz driver board kit...How do I interface the geckos drivers...