CAD CAM EDM DRO - Yahoo Group Archive

Re: Question? UCN5804

Posted by Richard
on 2003-07-02 13:50:16 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<davemucha@j...> wrote:
>
> if you put 10 resistors, 10K, in parallel, you get 1 K total


Dave, I have started with a 10 watt wirewound at 1000 ohms or so,
break the case, unwind the coiled resistance wire, measure off about
200 ohms worth which will be about an inch or so and should,with
crimped on lugs, do the job. Inductance should be no more that any
piece of wire the same measurements and the inter-turn capacitance
should be gone. We did this all the time when I was playing with
radio gear back in WW2! I have also done it when needing a low value
resistor to provide a feedback voltage to a comparator for current
limiting applications.

Discussion Thread

k00lmon 2003-06-16 21:26:30 UTC Question? UCN5804 stephank97 2003-06-17 01:08:05 UTC Re: Question? UCN5804 James Stevens 2003-06-17 06:23:32 UTC Re: [CAD_CAM_EDM_DRO] Question? UCN5804 Raymond Heckert 2003-06-17 21:05:20 UTC Re: [CAD_CAM_EDM_DRO] Question? UCN5804 Alan Marconett KM6VV 2003-06-18 10:36:53 UTC Re: [CAD_CAM_EDM_DRO] Question? UCN5804 ben_englund 2003-07-02 00:18:32 UTC Re: Question? UCN5804 ccq@x... 2003-07-02 05:01:54 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 Harvey White 2003-07-02 06:13:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 Carl Mikkelsen 2003-07-02 06:33:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 ccq@x... 2003-07-02 07:06:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 turbulatordude 2003-07-02 07:09:59 UTC Re: Question? UCN5804 Eric Rullens 2003-07-02 07:58:21 UTC RE: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 Alan Marconett KM6VV 2003-07-02 10:47:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 turbulatordude 2003-07-02 11:58:29 UTC Re: Question? UCN5804 Richard 2003-07-02 13:50:16 UTC Re: Question? UCN5804 chrlythb@a... 2003-07-02 18:10:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 JanRwl@A... 2003-07-02 19:21:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 turbulatordude 2003-07-02 20:21:28 UTC Re: Question? UCN5804 Bill Kichman 2003-07-03 10:13:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 JanRwl@A... 2003-07-03 11:27:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804 turbulatordude 2003-07-03 16:05:00 UTC Re: Question? UCN5804 Paul Alciatore 2003-07-31 13:30:57 UTC Re: Question? UCN5804