Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
Posted by
JanRwl@A...
on 2003-07-02 19:21:24 UTC
In a message dated 7/2/2003 8:12:47 PM Central Standard Time,
chrlythb@... writes:
electrically connected VERY, VERY carefully! NOT a practical proposition with that
many TINY parts!
[Non-text portions of this message have been removed]
chrlythb@... writes:
> Couldn't they use 20 100K 1/4 watt resistors?Charlie: This would result in 5K at 5W, but ONLY if mechanically and
>
electrically connected VERY, VERY carefully! NOT a practical proposition with that
many TINY parts!
[Non-text portions of this message have been removed]
Discussion Thread
k00lmon
2003-06-16 21:26:30 UTC
Question? UCN5804
stephank97
2003-06-17 01:08:05 UTC
Re: Question? UCN5804
James Stevens
2003-06-17 06:23:32 UTC
Re: [CAD_CAM_EDM_DRO] Question? UCN5804
Raymond Heckert
2003-06-17 21:05:20 UTC
Re: [CAD_CAM_EDM_DRO] Question? UCN5804
Alan Marconett KM6VV
2003-06-18 10:36:53 UTC
Re: [CAD_CAM_EDM_DRO] Question? UCN5804
ben_englund
2003-07-02 00:18:32 UTC
Re: Question? UCN5804
ccq@x...
2003-07-02 05:01:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
Harvey White
2003-07-02 06:13:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
Carl Mikkelsen
2003-07-02 06:33:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
ccq@x...
2003-07-02 07:06:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
turbulatordude
2003-07-02 07:09:59 UTC
Re: Question? UCN5804
Eric Rullens
2003-07-02 07:58:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
Alan Marconett KM6VV
2003-07-02 10:47:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
turbulatordude
2003-07-02 11:58:29 UTC
Re: Question? UCN5804
Richard
2003-07-02 13:50:16 UTC
Re: Question? UCN5804
chrlythb@a...
2003-07-02 18:10:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
JanRwl@A...
2003-07-02 19:21:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
turbulatordude
2003-07-02 20:21:28 UTC
Re: Question? UCN5804
Bill Kichman
2003-07-03 10:13:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
JanRwl@A...
2003-07-03 11:27:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Question? UCN5804
turbulatordude
2003-07-03 16:05:00 UTC
Re: Question? UCN5804
Paul Alciatore
2003-07-31 13:30:57 UTC
Re: Question? UCN5804