Re: availability of composite multiconductor cable?

You might want to check out:

http://www.action-electronics.com/cabl-prc.htm

They list a number choice in 22AWG with shielding.


Steve S.


--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Carlos Guillermo"
<carlos@v...> wrote:

> Try these too:
>
> http://www.sabawp.com/HTMLobj-448/servousa4.pdf
> http://www.sabawp.com/HTMLobj-446/servousa2.pdf
> http://www.sabawp.com/HTMLobj-449/servousa5.pdf
> http://www.lappcableasia.com/ under catalog - Olflex Servo Cables
>
>
> Regards,
>
> Carlos Guillermo
> VERVE Engineering & Design
>
> -----Original Message-----
> From: Carlos Guillermo [mailto:carlos@v...]
> Sent: Saturday, July 19, 2003 3:00 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: RE: [CAD_CAM_EDM_DRO] availability of composite
> multiconductor cable?
>
> Try these guys. Probably pricey, but for only a few feet, the
> total bill can't be too high. Let us know?
>
> http://www.alphawire.com/pages/103.cfm?partner=0?=0
>
> Regards,
>
> Carlos Guillermo
> VERVE Engineering & Design
>
> -----Original Message-----
> From: David A. Frantz [mailto:wizard@e...]
> Sent: Saturday, July 19, 2003 2:35 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] availability of composite
> multiconductor cable?
>
> While I realize these are available, are you sure you really want
> to do
> this??.
>
> I've seeen motor leads interfer with encodered signals when they
> are run
> side by side in seperate shielded cables. This really seems to
> be a
> case of asking for trouble.
>
> Dave
>
>
> mrgamber wrote:
>
> >Instead of running 2 cables to my servo's, I'd rather run 1
> composite
> >of 14 or 16 AWG pair with 4 or 5 22-24AWG. shielded of course.
> >
> >Where do I buy such a beast?
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@a..., timg@k...
> Moderator: pentam@c... indigo_red@q... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to
> be a sister site to the CCED group, as many of the same members
> are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/