Hybrid Connectors Was Re: availability of composite multiconductor cable?
Posted by
mrgamber
on 2003-07-20 13:43:47 UTC
This is a servo system. I will have 1000uF caps on the motor power
inputs on the gecko 320's. What is meant by commodity motor drive?
Do Gecko 320's output PWM?
inputs on the gecko 320's. What is meant by commodity motor drive?
Do Gecko 320's output PWM?
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
>
>
> mrgamber wrote:
>
> >I'm looking at some hybrid d-shell connectors that have 2 power
pins
> >and 5 signal pins.
> >
> >If I use 2 seperate cables for power and signal, but they enter
the
> >backshell at 90 deg to each other, wire to their respective pins
and
> >then seperate again inside the box, will this still be a problem?
> >
> >As I understand it, running the wire for a distance in parallel is
> >the problem and not the being close in a few places.
> >
> >
> >
> The real problem is unfiltered PWM outputs on commodity motor
drives.
> I have had no problem with noise on the encoder or tach signals on
my
> servo system. But, I put a very effective output filter to remove
the
> high energy pulses on the PWM output to the motor. (I used shielded
> cable for the tach and encoder, anyway.) but, I run all the cables
parallel
> without any problem. Probably you can't do that with Gecko or Rutex
> drives.
>
> I used round circular plastic connectors from AMP. They have a
large
> choice of these in the Digi-Key catalog. I used some 27 pin
connectors
> with all the same size pins, rated at 5 Amps/pin. But, they do
have some
> with wide blade-like contacts in some positions, so you can have big
> ones for the motor and smaller for encoder, limit switches, etc.
>
> Jon
Discussion Thread
mrgamber
2003-07-19 11:13:01 UTC
availability of composite multiconductor cable?
David A. Frantz
2003-07-19 14:33:24 UTC
Re: [CAD_CAM_EDM_DRO] availability of composite multiconductor cable?
Carlos Guillermo
2003-07-19 15:03:03 UTC
RE: [CAD_CAM_EDM_DRO] availability of composite multiconductor cable?
Carlos Guillermo
2003-07-19 15:45:42 UTC
RE: [CAD_CAM_EDM_DRO] availability of composite multiconductor cable?
millfire2003
2003-07-19 18:23:27 UTC
Re: availability of composite multiconductor cable?
Myron Cherry
2003-07-19 19:10:00 UTC
Re: [CAD_CAM_EDM_DRO] availability of composite multiconductor cable?
mrgamber
2003-07-19 19:24:11 UTC
Re: availability of composite multiconductor cable?
David A. Frantz
2003-07-19 22:53:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: availability of composite multiconductor cable?
mrgamber
2003-07-20 07:44:29 UTC
Hybrid Connectors Was Re: availability of composite multiconductor cable?
David A. Frantz
2003-07-20 08:07:04 UTC
Re: [CAD_CAM_EDM_DRO] Hybrid Connectors Was Re: availability of composite multiconductor cable?
David A. Frantz
2003-07-20 08:53:02 UTC
Re: [CAD_CAM_EDM_DRO] Hybrid Connectors Was Re: availability of composite multiconductor cable?
Jon Elson
2003-07-20 12:36:59 UTC
Re: [CAD_CAM_EDM_DRO] Hybrid Connectors Was Re: availability of composite multiconductor cable?
mrgamber
2003-07-20 13:43:47 UTC
Hybrid Connectors Was Re: availability of composite multiconductor cable?
caudlet
2003-07-20 19:17:44 UTC
Hybrid Connectors Was Re: availability of composite multiconductor cable?
Jon Elson
2003-07-20 21:32:10 UTC
Re: [CAD_CAM_EDM_DRO] Hybrid Connectors Was Re: availability of composite multiconductor cable?