CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Dan's announcement

Posted by Dan Mauch
on 2000-03-23 14:38:30 UTC
I just ran in some more this morning. The basici system runs fine, the
problem is that it runs too slow. The best I could get out of a 200 Mhz
pentium was 23 IPM. The problem seem to be in the processing time. I know he
is working on the problem so I expect the output speeds to increase. The
estimated price is =<$100
Dan
-----Original Message-----
From: wanliker@... <wanliker@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Thursday, March 23, 2000 1:30 PM
Subject: Re: [CAD_CAM_EDM_DRO] Dan's announcement


>From: wanliker@...
>
>In a message dated 3/23/00 7:52:49 AM Mountain Standard Time,
>dmauch@... writes:
>
><< The software (emc dos real time) isn't quite ready. >>
>Any advance ideas on the prices?
>bill
>
>------------------------------------------------------------------------
>GET A NEXTCARD VISA, in 30 seconds! Get rates as low as 2.9%
>Intro or 9.9% Fixed APR and no hidden fees. Apply NOW!
>http://click.egroups.com/1/936/2/_/423600/_/953847055/
>------------------------------------------------------------------------
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems in the above catagories.
>To Unsubscribe, read archives, change to or from digest.
>Go to: http://www.onelist.com/isregistered.cgi
>Log on, and you will go to Member Center, and you can make changes there.
>For the FAQ, go to http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>

Discussion Thread

wanliker@a... 2000-03-22 18:01:54 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement Bob Bachman 2000-03-22 18:10:02 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement wanliker@a... 2000-03-22 18:33:29 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement Dan Mauch 2000-03-23 06:51:19 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement stratton@m... 2000-03-23 07:14:51 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement jguenthe 2000-03-23 07:22:34 UTC RE: [CAD_CAM_EDM_DRO] Dan's announcement Dan Mauch 2000-03-23 08:49:46 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement wanliker@a... 2000-03-23 13:30:54 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement Dan Mauch 2000-03-23 14:38:30 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement wanliker@a... 2000-03-25 09:04:45 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement Dan Mauch 2000-03-25 11:26:10 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement wanliker@a... 2000-03-25 15:31:37 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement wanliker@a... 2000-03-26 08:16:24 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement Steve Carlisle 2000-03-26 08:31:49 UTC Re: [CAD_CAM_EDM_DRO] Dan's announcement Tim Goldstein 2000-03-26 11:07:28 UTC RE: [CAD_CAM_EDM_DRO] Dan's announcement Tim Goldstein 2000-03-26 17:54:42 UTC DeskNCRT Fred Smith 2000-03-27 17:42:25 UTC Re: RE: [CAD_CAM_EDM_DRO] Dan's announcement Bob Bachman 2000-03-29 15:53:54 UTC Re: [CAD_CAM_EDM_DRO] DeskNCRT joe 2000-07-04 06:48:26 UTC DeskNCRT