CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Reduction by 10

Posted by ccq@x...
on 2003-10-17 14:26:03 UTC
On Fri Oct 17 12:12:56 2003 Torsten wrote:

>--- In CAD_CAM_EDM_DRO@yahoogroups.com, ccq@x wrote:
>> On timing belt setups, does a reduction of 10 requier a 5" wheel
>driven by a 2"
>> wheel, or would it be 5":2":1"?
>>
>> Bill
>
>On Timing Belts the ratios are determined by the tooth count.
>You have to decide on a belt type first they differentiate
>in pitch and size a 30 tooth "L" type would have a larger
>diameter then a "XL" type of the same tooth count.
>A combination of a 15 tooth and a 30 tooth will give a 1:2 ratio,
>10 tooth and a 30 tooth will give 1:3 ratio and so on.
>The key to choosing the right Tooth count is in the smaller
>Pulley a minimum tooth count is required for smooth operation
>more teeth are better.
>The larger Pulley is determined by the choosen ratio the dia.
>of this Pulley will have to be looked up in the MFG specs.
>Good Luck

Now I get it; Ok, thanks.

Bill


--
----------------------------------------------------------------------------
RKBA! ***** Blessings On Thee, Oh Israel! ***** 4-19!
----------------+----------+--------------------------+---------------------
An _EFFECTIVE_ | Insured | All matter is vibration. | Let he who hath no
weapon in every | by COLT; | -- Max Planck | weapon sell his
hand = Freedom | DIAL | In the beginning was the | garment and buy a
on every side! | 1911-A1. | word. -- The Bible | sword.--Jesus Christ
----------------+----------+--------------------------+---------------------

Constitutional Government is dead; LONG LIVE THE CONSTITUTION!!!!!

----------------------------------------------------------------------------

Discussion Thread

washcomp 2003-10-16 07:17:31 UTC Control Pendant/Panel layout for your comments wanliker@a... 2003-10-16 07:44:44 UTC Re: [CAD_CAM_EDM_DRO] Control Pendant/Panel layout for your comments washcomp 2003-10-16 16:05:32 UTC Re: Control Pendant/Panel layout for your comments wanliker@a... 2003-10-16 18:02:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Control Pendant/Panel layout for your comments washcomp 2003-10-16 23:41:37 UTC Re: Control Pendant/Panel layout for your comments wanliker@a... 2003-10-16 23:47:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Control Pendant/Panel layout for your comments ccq@x... 2003-10-17 04:37:48 UTC Reduction by 10 vavaroutsos 2003-10-17 09:11:10 UTC Re: Reduction by 10 ccq@x... 2003-10-17 11:05:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Reduction by 10 Torsten 2003-10-17 12:13:01 UTC Re: Reduction by 10 ccq@x... 2003-10-17 14:26:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Reduction by 10 caudlet 2003-10-17 16:39:07 UTC Re: Control Pendant/Panel layout for your comments Raymond Heckert 2003-10-17 20:00:02 UTC Re: [CAD_CAM_EDM_DRO] Re: Reduction by 10 washcomp 2003-10-17 20:00:38 UTC Re: Control Pendant/Panel layout for your comments