Re: Control Pendant/Panel layout for your comments
Posted by
washcomp
on 2003-10-16 23:41:37 UTC
I'm with you. Currently my E-Stop button is a NC in series with the
latching contact on my enable relay. When pressed, the relay drops
out and cuts the power to the stepper drives, the mill's spindle
motor and invokes the spindle clamp and brake. In order to re-
start, the "Start" button must be pressed. Using the "Start" button
to kick in the enable relay means that transients and other stuff
will not affect anything when the PC starts up. It works as well as
other schemes (like the charge pump circuit), but only requires a
switch latched relay contact.
Regards,
Jeff
latching contact on my enable relay. When pressed, the relay drops
out and cuts the power to the stepper drives, the mill's spindle
motor and invokes the spindle clamp and brake. In order to re-
start, the "Start" button must be pressed. Using the "Start" button
to kick in the enable relay means that transients and other stuff
will not affect anything when the PC starts up. It works as well as
other schemes (like the charge pump circuit), but only requires a
switch latched relay contact.
Regards,
Jeff
--- In CAD_CAM_EDM_DRO@yahoogroups.com, wanliker@a... wrote:
> In a message dated 10/16/2003 5:07:05 PM Mountain Daylight Time,
> jeff@w... writes:
>
> >
> > I took your advice and made a couple of other changes. Please
let me
> > know (or anyone else who wants to chime in) what you think of
the
> > redesign:
> >
> Looks pretty good to me, Be sure the E Stop latches when punched,
or use it
> in conjunction with a relay so once it is dropped out that it
can't restart
> without physical input from you. Again I am paranoid on E Stops.
> bill
>
>
> [Non-text portions of this message have been removed]
Discussion Thread
washcomp
2003-10-16 07:17:31 UTC
Control Pendant/Panel layout for your comments
wanliker@a...
2003-10-16 07:44:44 UTC
Re: [CAD_CAM_EDM_DRO] Control Pendant/Panel layout for your comments
washcomp
2003-10-16 16:05:32 UTC
Re: Control Pendant/Panel layout for your comments
wanliker@a...
2003-10-16 18:02:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Control Pendant/Panel layout for your comments
washcomp
2003-10-16 23:41:37 UTC
Re: Control Pendant/Panel layout for your comments
wanliker@a...
2003-10-16 23:47:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Control Pendant/Panel layout for your comments
ccq@x...
2003-10-17 04:37:48 UTC
Reduction by 10
vavaroutsos
2003-10-17 09:11:10 UTC
Re: Reduction by 10
ccq@x...
2003-10-17 11:05:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Reduction by 10
Torsten
2003-10-17 12:13:01 UTC
Re: Reduction by 10
ccq@x...
2003-10-17 14:26:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Reduction by 10
caudlet
2003-10-17 16:39:07 UTC
Re: Control Pendant/Panel layout for your comments
Raymond Heckert
2003-10-17 20:00:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Reduction by 10
washcomp
2003-10-17 20:00:38 UTC
Re: Control Pendant/Panel layout for your comments