Re: Ballscrew question
Posted by
yodawill2000
on 2004-02-25 11:57:44 UTC
C.S ..
Do they have a website ??
Or a # ??
Thanks for the info ...
if they are considerably less I'll go with the double nut setup .
Do they have a website ??
Or a # ??
Thanks for the info ...
if they are considerably less I'll go with the double nut setup .
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "C.S. Mo" <cs@v...> wrote:
> Rockford Ballscrew offers 5/8" rolled ballscrews for significantly
less.
> And, they will machine the ends for $60/end or anneal the ends for
$10/end.
>
> I initially went with a single nut with oversized ball bearings on
my
> quill assembly but found that I got 0.0015-0.002" backlash. Going
to a
> dual nut pre-loaded assembly reduced that to about 0.0002-5".
>
> --C.S.
>
> >Just to clarify Ray ..
> >Thats with the single nut assy ??
> >The Thompson rig is exactly what I was looking at ..
> >Decent pricing over at homeshopcnc ..
> >I'll just need to figure out how to turn the ends down ..
> >My lathe has only a 1/2" through hole ... Dooh !! :)
> >Thanks
> >>
> >> I get about 0.002 lash with the 5/8 thompson rolled screws.
> >>
> >> Ray
Discussion Thread
yodawill2000
2004-02-24 19:56:11 UTC
Ballscrew question
Roy J. Tellason
2004-02-24 22:12:40 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew question
Kenneth Cardolino
2004-02-25 03:25:27 UTC
Re: Ballscrew question
Ray Henry
2004-02-25 05:05:58 UTC
Re: Re: Ballscrew question
Ron Thompson
2004-02-25 07:33:42 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew question
yodawill2000
2004-02-25 07:46:27 UTC
Re: Ballscrew question
C.S. Mo
2004-02-25 08:52:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
yodawill2000
2004-02-25 11:57:44 UTC
Re: Ballscrew question
yodawill2000
2004-02-25 11:58:15 UTC
Re: Ballscrew question
C.S. Mo
2004-02-25 12:16:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
JanRwl@A...
2004-02-25 12:46:01 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew question
Paul
2004-02-25 13:23:27 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew question
Douglas Pollard
2004-02-25 15:04:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
Ron Thompson
2004-02-25 15:15:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
Greg Nuspel
2004-02-25 16:12:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
Paul
2004-02-25 17:39:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
C.S. Mo
2004-02-25 17:58:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
Raymond Heckert
2004-02-25 19:39:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
JanRwl@A...
2004-02-25 20:07:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
Roy J. Tellason
2004-02-25 20:39:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
Ron Thompson
2004-02-25 20:49:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
industrialhobbies
2004-02-25 22:07:21 UTC
Re: Ballscrew question
industrialhobbies
2004-02-25 22:07:27 UTC
Re: Ballscrew question
Paul
2004-02-27 09:19:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
ballendo
2004-02-27 17:09:31 UTC
Re: Ballscrew question
Paul
2004-02-27 18:55:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
Lee Leathers
2004-02-27 19:00:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
Paul
2004-02-27 19:23:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew question
ballendo
2004-02-28 06:32:36 UTC
Re: Ballscrew question
industrialhobbies
2004-03-01 00:19:11 UTC
Choosing 3/4 or 5/8 screw was Re: Ballscrew question