CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] 28v power transformer

on 2004-04-21 11:54:16 UTC
Hi Bob,

You probably have two primaries. Wire them in parallel for 120v. Check
out the schematic in the files section under Driver/PS.

Alan KM6VV

stcnc2000 wrote:
>
> Hi,
> I'm building a power supply kit. I have a question on the primary
> side of the transformer, which has four wires. How do i wire this to
> 110 vac?
> thanks
> Bob
>
>

Discussion Thread

stcnc2000 2004-04-21 09:52:00 UTC 28v power transformer Andy Wander 2004-04-21 10:06:22 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Robert Campbell 2004-04-21 10:09:51 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer theowyn 2004-04-21 10:26:35 UTC Re: 28v power transformer Roy J. Tellason 2004-04-21 10:31:43 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer Roy J. Tellason 2004-04-21 10:40:30 UTC Re: [CAD_CAM_EDM_DRO] Re: 28v power transformer Andy Wander 2004-04-21 10:42:45 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Andy Wander 2004-04-21 10:48:21 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Roy J. Tellason 2004-04-21 10:55:18 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer Andy Wander 2004-04-21 10:58:14 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Roy J. Tellason 2004-04-21 11:14:37 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer theowyn 2004-04-21 11:21:25 UTC Re: 28v power transformer Alan Marconett KM6VV 2004-04-21 11:54:16 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer stcnc2000 2004-04-21 13:45:03 UTC Re: 28v power transformer Andy Wander 2004-04-21 13:55:23 UTC RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer stcnc2000 2004-04-21 14:00:58 UTC Re: 28v power transformer stcnc2000 2004-04-21 14:06:16 UTC Re: 28v power transformer Andy Wander 2004-04-21 14:11:09 UTC RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer stcnc2000 2004-04-21 14:20:59 UTC Re: 28v power transformer Andy Wander 2004-04-21 14:27:32 UTC RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer stcnc2000 2004-04-21 14:46:09 UTC Re: 28v power transformer Andy Wander 2004-04-21 15:02:59 UTC RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer stcnc2000 2004-04-21 15:23:12 UTC Re: 28v power transformer stcnc2000 2004-04-21 16:13:40 UTC Re: 28v power transformer Larry Edinger 2004-04-21 17:08:25 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer Alan Marconett KM6VV 2004-04-21 17:29:14 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer JanRwl@A... 2004-04-21 18:52:23 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer Roy J. Tellason 2004-04-21 20:37:18 UTC Re: [CAD_CAM_EDM_DRO] Re: 28v power transformer Robert Adams 2004-04-24 07:09:41 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Andy Wander 2004-04-24 19:35:06 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer