RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer

Is it a bridge(4-diodes, 4 terminals) or just a full-wave(2 diodes, 3
terminals)?

Andy Wander
Verrex Corporation


-----Original Message-----
From: stcnc2000 [mailto:thinkcnc@...]
Sent: Wednesday, April 21, 2004 5:05 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: 28v power transformer

--- In CAD_CAM_EDM_DRO@yahoogroups.com, Andy Wander <awander@v...>
wrote:

> Are you using a full-wav, half-wave, or full-wave bridge rectifier?
>
> Andy Wander
> Verrex Corporation
>
>
> -----Original Message-----
> From: stcnc2000 [mailto:thinkcnc@h...]
> Sent: Wednesday, April 21, 2004 4:45 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: 28v power transformer
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan Marconett KM6VV
> <KM6VV@a...> wrote:
> > Hi Bob,
> >
> > You probably have two primaries. Wire them in parallel for

120v.

> Check
> > out the schematic in the files section under Driver/PS.
> >
> > Alan KM6VV
> >
> > stcnc2000 wrote:
> > >
> > > Hi,
> > > I'm building a power supply kit. I have a question on the

primary

> > > side of the transformer, which has four wires. How do i wire

this

> to
> > > 110 vac?
> > > thanks
> > > Bob
> > > Thanks for the info. I tried that and only get about 17vdc at
> rectifer. The transformer i'm using is (MPJA) LP-437 18vct(9-0-9)
> 2amps.
> > >
> I'm using a full-wave bridge.
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@a...,
> timg@k...
> Moderator: pentam@c... indigo_red@q... davemucha@j...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to

reach it if

> you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to

be a

> sister site to the CCED group, as many of the same members are

there, for OT

> subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING

THEM.

> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links