CAD CAM EDM DRO - Yahoo Group Archive

Re: 28v power transformer

Posted by stcnc2000
on 2004-04-21 14:46:09 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Andy Wander <awander@v...>
wrote:
> and only get about 17vdc at
> > > rectifer. The transformer i'm using is (MPJA) LP-437 18vct(9-0-
9)
> > > 2amps.
> > > > >
> > > I'm using a full-wave bridge.
> > > It is 4 diodes and 4 terminals.
> No load, 20 vac into the bridge, No Filter Cap connected yet have a
15,000 uf 50v, Yes the bridge is hook up correct AC to Ac and then i
measure across + and - terminals.

> Is this measurement with any kind of a load on the supply?
> Have you measured the AC voltage going into the rectifier?
> What kind of filter capacitor are you using?
> And are you sure the rectifier is hooked up correctly?

Discussion Thread

stcnc2000 2004-04-21 09:52:00 UTC 28v power transformer Andy Wander 2004-04-21 10:06:22 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Robert Campbell 2004-04-21 10:09:51 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer theowyn 2004-04-21 10:26:35 UTC Re: 28v power transformer Roy J. Tellason 2004-04-21 10:31:43 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer Roy J. Tellason 2004-04-21 10:40:30 UTC Re: [CAD_CAM_EDM_DRO] Re: 28v power transformer Andy Wander 2004-04-21 10:42:45 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Andy Wander 2004-04-21 10:48:21 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Roy J. Tellason 2004-04-21 10:55:18 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer Andy Wander 2004-04-21 10:58:14 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Roy J. Tellason 2004-04-21 11:14:37 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer theowyn 2004-04-21 11:21:25 UTC Re: 28v power transformer Alan Marconett KM6VV 2004-04-21 11:54:16 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer stcnc2000 2004-04-21 13:45:03 UTC Re: 28v power transformer Andy Wander 2004-04-21 13:55:23 UTC RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer stcnc2000 2004-04-21 14:00:58 UTC Re: 28v power transformer stcnc2000 2004-04-21 14:06:16 UTC Re: 28v power transformer Andy Wander 2004-04-21 14:11:09 UTC RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer stcnc2000 2004-04-21 14:20:59 UTC Re: 28v power transformer Andy Wander 2004-04-21 14:27:32 UTC RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer stcnc2000 2004-04-21 14:46:09 UTC Re: 28v power transformer Andy Wander 2004-04-21 15:02:59 UTC RE: [CAD_CAM_EDM_DRO] Re: 28v power transformer stcnc2000 2004-04-21 15:23:12 UTC Re: 28v power transformer stcnc2000 2004-04-21 16:13:40 UTC Re: 28v power transformer Larry Edinger 2004-04-21 17:08:25 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer Alan Marconett KM6VV 2004-04-21 17:29:14 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer JanRwl@A... 2004-04-21 18:52:23 UTC Re: [CAD_CAM_EDM_DRO] 28v power transformer Roy J. Tellason 2004-04-21 20:37:18 UTC Re: [CAD_CAM_EDM_DRO] Re: 28v power transformer Robert Adams 2004-04-24 07:09:41 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer Andy Wander 2004-04-24 19:35:06 UTC RE: [CAD_CAM_EDM_DRO] 28v power transformer