CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] CNC Controler Software

Posted by Paul
on 2004-08-23 10:10:11 UTC
Hi Jon.

Very approximate figures indeed - I have managed to push EMC to approx 65KHz
on a 1.8GHz Athlon box, but jitter induced by hardware constraints were high.
At this high rate, text mode or remote GUI options were deemed to be
preferrable to running a GUI on the same computer.
With entry level computers now supplied with 2.4GHz processors or faster, it
would be worth retesting to see what the practical upper limit is.

Regards, Paul.


On Monday 23 August 2004 17:32, Jon Elson wrote:
>  EMC has a limit of about 25,000 steps/second, Mach2 is
> about 40,000.
> These are approximate, as some motor/driver combinations can tolerate the
> rough timing better than others.

--
irc channel for EMC users at irc.freenode.org
/join #emc

Pieces of seven! Pieces of seven! (Hrm, parroty error)

Discussion Thread

archie5594 2004-08-23 05:03:46 UTC CNC Controler Software Paul 2004-08-23 06:00:16 UTC Re: [CAD_CAM_EDM_DRO] CNC Controler Software Stan Aarhus 2004-08-23 06:44:56 UTC Re: [CAD_CAM_EDM_DRO] CNC Controler Software Jones, Joseph A1 2004-08-23 07:07:37 UTC RE: [CAD_CAM_EDM_DRO] CNC Controler Software Tony Jeffree 2004-08-23 07:29:30 UTC RE: [CAD_CAM_EDM_DRO] CNC Controler Software caudlet 2004-08-23 09:35:40 UTC Re: CNC Controler Software Jon Elson 2004-08-23 09:37:40 UTC Re: [CAD_CAM_EDM_DRO] CNC Controler Software Fred Smith 2004-08-23 09:49:58 UTC Re: CNC Controler Software Paul 2004-08-23 10:10:11 UTC Re: [CAD_CAM_EDM_DRO] CNC Controler Software Steven Ciciora 2004-08-23 11:49:11 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Controller Software Jones, Joseph A1 2004-08-23 12:21:51 UTC RE: [CAD_CAM_EDM_DRO] Re: CNC Controller Software Tom Hubin 2004-08-23 13:08:50 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Controller Software Jones, Joseph A1 2004-08-23 13:23:43 UTC RE: [CAD_CAM_EDM_DRO] Re: CNC Controller Software Dan Mauch 2004-08-23 13:51:56 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Controller Software cadman456 2004-08-23 17:35:19 UTC Re: CNC Controller Software james_cullins@s... 2004-08-23 19:07:22 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Controller Software volitan712003 2004-08-24 19:29:46 UTC Re: CNC Controler Software RH 2004-08-25 06:47:35 UTC CNC - The Basics Andy Wander 2004-08-25 07:04:25 UTC RE: [CAD_CAM_EDM_DRO] CNC - The Basics Robert Campbell 2004-08-25 09:47:43 UTC Re: [CAD_CAM_EDM_DRO] CNC - The Basics Jon Elson 2004-08-25 10:24:45 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Controler Software volitan712003 2004-08-29 05:45:56 UTC Re: CNC Controler Software Jon Elson 2004-08-29 21:46:44 UTC Re: [CAD_CAM_EDM_DRO] Re: CNC Controler Software