Re: CNC Controler Software
Posted by
volitan712003
on 2004-08-29 05:45:56 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
have to use EMC if I wanted to use these boards?
Thanks
David
> No, it doesn't work with pulses at all. It works like a servosystem,
> with a motorreports
> that runs at a controlled velocity, and a position counter that
> exactIs this a "mode" of output that TurboCNC is not capable of? Would I
> position. If you have encoders on the machine, it can count signals
> from them,
> otherwise it counts the step pulses going out.
>
> Jon
have to use EMC if I wanted to use these boards?
Thanks
David
Discussion Thread
archie5594
2004-08-23 05:03:46 UTC
CNC Controler Software
Paul
2004-08-23 06:00:16 UTC
Re: [CAD_CAM_EDM_DRO] CNC Controler Software
Stan Aarhus
2004-08-23 06:44:56 UTC
Re: [CAD_CAM_EDM_DRO] CNC Controler Software
Jones, Joseph A1
2004-08-23 07:07:37 UTC
RE: [CAD_CAM_EDM_DRO] CNC Controler Software
Tony Jeffree
2004-08-23 07:29:30 UTC
RE: [CAD_CAM_EDM_DRO] CNC Controler Software
caudlet
2004-08-23 09:35:40 UTC
Re: CNC Controler Software
Jon Elson
2004-08-23 09:37:40 UTC
Re: [CAD_CAM_EDM_DRO] CNC Controler Software
Fred Smith
2004-08-23 09:49:58 UTC
Re: CNC Controler Software
Paul
2004-08-23 10:10:11 UTC
Re: [CAD_CAM_EDM_DRO] CNC Controler Software
Steven Ciciora
2004-08-23 11:49:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Controller Software
Jones, Joseph A1
2004-08-23 12:21:51 UTC
RE: [CAD_CAM_EDM_DRO] Re: CNC Controller Software
Tom Hubin
2004-08-23 13:08:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Controller Software
Jones, Joseph A1
2004-08-23 13:23:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: CNC Controller Software
Dan Mauch
2004-08-23 13:51:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Controller Software
cadman456
2004-08-23 17:35:19 UTC
Re: CNC Controller Software
james_cullins@s...
2004-08-23 19:07:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Controller Software
volitan712003
2004-08-24 19:29:46 UTC
Re: CNC Controler Software
RH
2004-08-25 06:47:35 UTC
CNC - The Basics
Andy Wander
2004-08-25 07:04:25 UTC
RE: [CAD_CAM_EDM_DRO] CNC - The Basics
Robert Campbell
2004-08-25 09:47:43 UTC
Re: [CAD_CAM_EDM_DRO] CNC - The Basics
Jon Elson
2004-08-25 10:24:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Controler Software
volitan712003
2004-08-29 05:45:56 UTC
Re: CNC Controler Software
Jon Elson
2004-08-29 21:46:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNC Controler Software