CAD CAM EDM DRO - Yahoo Group Archive

Re: new stepper motors wiring mess ?fixed!

Posted by Keith Clark
on 2004-08-28 13:10:10 UTC
No, the spindle is still coming through the mill's power since it is
220 v 3 phase. I wonder where I could find a big honking UPS for
the spindle... NOT!

Keith

--- In CAD_CAM_EDM_DRO@yahoogroups.com, Stephen Wille Padnos
<spadnos@s...> wrote:
> And the spindle motor? That must be a honking big UPS!!
>
> - Steve
>
> Andy Wander wrote:
>
> >Keith:
> >
> >I can understand plugging your PC into a UPS, but the Stepper
motor Power
> >Supply?
> >
> >Andy Wander
> >Verrex Corporation
> >
> >
> > -----Original Message-----
> >From: Keith Clark [mailto:mail@t...]
> >Sent: Saturday, August 28, 2004 2:10 PM
> >To: CAD_CAM_EDM_DRO@yahoogroups.com
> >Subject: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring
mess ?fixed!
> >
> >I am using the battery backup, power surge protection for my
> >computer since there are so many power surges and dirty
electricity
> >in my neighborhood. Surges have apparently destroyed the motion
> >card 2 times prior to using the protection. I don't count on it
for
> >saving any information but I hope it would finish milling a part
> >before shutting off if there was a power failure.
> >
> >Keith
> >

Discussion Thread

Keith Clark 2004-08-27 23:42:20 UTC new stepper motors wiring mess... Keith Clark 2004-08-28 06:57:52 UTC Re: new stepper motors wiring mess ?fixed! james_cullins@s... 2004-08-28 07:27:19 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! Harvey White 2004-08-28 07:39:20 UTC Re: [CAD_CAM_EDM_DRO] new stepper motors wiring mess... Keith Clark 2004-08-28 07:40:16 UTC Re: new stepper motors wiring mess ?fixed! Harvey White 2004-08-28 07:40:47 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! R Rogers 2004-08-28 07:53:49 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! R Rogers 2004-08-28 07:54:27 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! Keith Clark 2004-08-28 11:09:53 UTC Re: new stepper motors wiring mess ?fixed! Keith Clark 2004-08-28 11:14:42 UTC Re: new stepper motors wiring mess... erie 2004-08-28 11:23:45 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess... Jon Elson 2004-08-28 11:26:17 UTC Re: [CAD_CAM_EDM_DRO] new stepper motors wiring mess... erie 2004-08-28 11:26:50 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess... Keith Clark 2004-08-28 11:32:49 UTC Re: new stepper motors wiring mess... Andy Wander 2004-08-28 11:47:45 UTC RE: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! Stephen Wille Padnos 2004-08-28 11:54:30 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! Andy Wander 2004-08-28 11:55:02 UTC RE: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess... Stephen Wille Padnos 2004-08-28 12:02:30 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess... erie 2004-08-28 12:22:49 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! Harvey White 2004-08-28 13:00:02 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess... Keith Clark 2004-08-28 13:08:08 UTC Re: new stepper motors wiring mess ?fixed! Keith Clark 2004-08-28 13:10:10 UTC Re: new stepper motors wiring mess ?fixed! Keith Clark 2004-08-28 13:12:42 UTC Re: new stepper motors wiring mess... Andy Wander 2004-08-28 13:14:32 UTC RE: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! Andy Wander 2004-08-28 13:15:41 UTC RE: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess... Keith Clark 2004-08-28 13:27:48 UTC Re: new stepper motors wiring mess ?fixed! erie 2004-08-28 13:31:07 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! Stephen Wille Padnos 2004-08-28 13:46:21 UTC Re: [CAD_CAM_EDM_DRO] Re: new stepper motors wiring mess ?fixed! metlmunchr 2004-08-29 10:05:10 UTC Re: new stepper motors wiring mess ?fixed! Keith Clark 2004-08-29 10:21:40 UTC Re: new stepper motors wiring mess ?fixed!