Re: [CAD_CAM_EDM_DRO] HP plotter servo
Posted by
josef wagner
on 2004-10-21 23:36:03 UTC
good morning dave
i am afraid these motors are in the power range of 10 to 15 Watt only.
and for the three axis control you need at least 80 to 100 watt if you are
going to use a mill tool of say 5 mm diameter.
some years ago i have got two of such HP motors from a plotter
and used them in gauge I railway models for single axle drive - was
jsut sufficient, the motor size was 42 mm diamter and 75 mm length without
decoder
best regards from vienna
josef wagner
+++
i am afraid these motors are in the power range of 10 to 15 Watt only.
and for the three axis control you need at least 80 to 100 watt if you are
going to use a mill tool of say 5 mm diameter.
some years ago i have got two of such HP motors from a plotter
and used them in gauge I railway models for single axle drive - was
jsut sufficient, the motor size was 42 mm diamter and 75 mm length without
decoder
best regards from vienna
josef wagner
+++
----- Original Message -----
From: "turbulatordude" <davemucha@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Friday, October 22, 2004 8:16 AM
Subject: [CAD_CAM_EDM_DRO] HP plotter servo
16 volts.
> Has anyone ever tried to use the plotter motors ?
> Dave
> South Jersey
Discussion Thread
turbulatordude
2004-10-21 23:16:36 UTC
HP plotter servo
josef wagner
2004-10-21 23:36:03 UTC
Re: [CAD_CAM_EDM_DRO] HP plotter servo
Jon Elson
2004-10-22 09:01:10 UTC
Re: [CAD_CAM_EDM_DRO] HP plotter servo
turbulatordude
2004-10-22 09:31:35 UTC
Re: HP plotter servo
washcomp
2004-10-22 12:18:12 UTC
Re: HP plotter servo
Graham Stabler
2004-10-22 13:30:40 UTC
Re: HP plotter servo
volitan712003
2004-10-22 14:10:08 UTC
Re: HP plotter servo
learnningstuff
2004-10-22 16:16:46 UTC
Re: HP plotter servo
turbulatordude
2004-10-22 16:18:52 UTC
Re: HP plotter servo
Jeff Demand
2004-10-22 16:55:48 UTC
Re: HP plotter servo
Graham Stabler
2004-10-22 17:55:16 UTC
Re: HP plotter servo
Fred Smith
2004-10-22 20:30:44 UTC
Re: HP plotter servo
Mariss Freimanis
2004-10-22 23:27:16 UTC
Re: HP plotter servo
Jeff Jones
2004-10-23 01:35:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: HP plotter servo
Mariss Freimanis
2004-10-23 01:46:31 UTC
Re: HP plotter servo
Graham Stabler
2004-10-23 07:47:33 UTC
Re: HP plotter servo
Jeff Jones
2004-10-23 10:25:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: HP plotter servo
turbulatordude
2004-10-24 07:37:19 UTC
Re: HP plotter servo
turbulatordude
2004-10-24 07:48:23 UTC
Re: HP plotter servo - schematics
Hugh Prescott
2004-10-24 08:26:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: HP plotter servo - schematics
turbulatordude
2004-10-25 20:39:14 UTC
Re: HP plotter servo - schematics
Don
2004-10-25 21:12:26 UTC
Re: HP plotter servo
turbulatordude
2004-10-25 22:38:58 UTC
Re: HP plotter servo
Don Rogers
2004-10-26 11:46:48 UTC
Re: HP plotter servo