Re: HP plotter servo
Posted by
turbulatordude
on 2004-10-22 16:18:52 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Graham Stabler" <eexgs@n...>
wrote:
dissasembled.
That would mean for me, 8 of these motors.
As I understand a Gecko 320 would probably work, but that is over
$100 each. I hope to build my entire machine for under $100.
Dave
wrote:
>drive
> I have an interest in this, I have taken apart several HP inkjets
> and they too use a servo motor except they also use a linear
> encoder. I was thinking a pair of such motors an encoders could
> make a great little laser cutter or similar. I threw away the
> boards but by looking at the components it may be possible to workcontrol
> back from the motor output just enough to at least have the amp
> section.
>
> Would geckos work with such small motors?
>
> One other thing is that there is an application note for PIC
> of servo motors, this might be a good route to take for some cheapoI have a total of 4 of the ploters. 3 intact and the one I
> step and direction servo control for small machines. Would be an
> interesting project.
>
> Graham
dissasembled.
That would mean for me, 8 of these motors.
As I understand a Gecko 320 would probably work, but that is over
$100 each. I hope to build my entire machine for under $100.
Dave
Discussion Thread
turbulatordude
2004-10-21 23:16:36 UTC
HP plotter servo
josef wagner
2004-10-21 23:36:03 UTC
Re: [CAD_CAM_EDM_DRO] HP plotter servo
Jon Elson
2004-10-22 09:01:10 UTC
Re: [CAD_CAM_EDM_DRO] HP plotter servo
turbulatordude
2004-10-22 09:31:35 UTC
Re: HP plotter servo
washcomp
2004-10-22 12:18:12 UTC
Re: HP plotter servo
Graham Stabler
2004-10-22 13:30:40 UTC
Re: HP plotter servo
volitan712003
2004-10-22 14:10:08 UTC
Re: HP plotter servo
learnningstuff
2004-10-22 16:16:46 UTC
Re: HP plotter servo
turbulatordude
2004-10-22 16:18:52 UTC
Re: HP plotter servo
Jeff Demand
2004-10-22 16:55:48 UTC
Re: HP plotter servo
Graham Stabler
2004-10-22 17:55:16 UTC
Re: HP plotter servo
Fred Smith
2004-10-22 20:30:44 UTC
Re: HP plotter servo
Mariss Freimanis
2004-10-22 23:27:16 UTC
Re: HP plotter servo
Jeff Jones
2004-10-23 01:35:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: HP plotter servo
Mariss Freimanis
2004-10-23 01:46:31 UTC
Re: HP plotter servo
Graham Stabler
2004-10-23 07:47:33 UTC
Re: HP plotter servo
Jeff Jones
2004-10-23 10:25:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: HP plotter servo
turbulatordude
2004-10-24 07:37:19 UTC
Re: HP plotter servo
turbulatordude
2004-10-24 07:48:23 UTC
Re: HP plotter servo - schematics
Hugh Prescott
2004-10-24 08:26:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: HP plotter servo - schematics
turbulatordude
2004-10-25 20:39:14 UTC
Re: HP plotter servo - schematics
Don
2004-10-25 21:12:26 UTC
Re: HP plotter servo
turbulatordude
2004-10-25 22:38:58 UTC
Re: HP plotter servo
Don Rogers
2004-10-26 11:46:48 UTC
Re: HP plotter servo