CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Turning Spindle Off and On

Posted by JamesCullins
on 2004-12-16 19:52:26 UTC
It will disable the out signals in the absents of the charge pump signal
form Mach2.
This signal is a tone of about 13 kHz. When Mach2 is reset the signal
appears and the out puts are enabled. If Mach2 isn't running then you get
nothing out.
Jim
----- Original Message -----
From: "turbulatordude" <dave_mucha@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, December 16, 2004 7:39 PM
Subject: [CAD_CAM_EDM_DRO] Re: Turning Spindle Off and On


>
>
>
> > ///What about opto-isolation? Wouldnt there be a risk of damaging
> the PC electronics wiring up auxillary equiptment directly to the
> port?
>
>
> All the SSR's I have looked at have opto isolation as well as do
> Gecko's.
>
>
> The Cambell board does offer additional features that may or may not
> be required.
>
> There are a lot of people who wire directly into the port, from
> electronics hobbyists, to telescope people to machine tool people.
>
> Also, for my machines on machine tools, I keep them dedicated and
> simple software loaded.
>
> If you plan to surf the internet and use your machine as a general
> purpose machine, while you use your Bridgeport, you accept the risk
> of a virus doing bad things as well as having your registry cluttered.
>
>
> > Other breakout boards have the ability to control Solid state
> relays however like the PMDX has no "watchdog" feature that monitors
> erroneous pulses from the PC (it didn't two years ago anyway and they
> didn't sound too concerned about changing it).
>
>
> I'm not sure what signal the Cambell board does that differentiates a
> signal to the port from an erroneous signal.
>
> Dave
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>

Discussion Thread

kadeshan 2004-12-16 10:27:30 UTC Turning Spindle Off and On R Rogers 2004-12-16 12:28:58 UTC Re: [CAD_CAM_EDM_DRO] Turning Spindle Off and On turbulatordude 2004-12-16 13:35:29 UTC Re: Turning Spindle Off and On R Rogers 2004-12-16 14:56:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Turning Spindle Off and On Fred Smith 2004-12-16 16:45:04 UTC Re: Turning Spindle Off and On turbulatordude 2004-12-16 17:40:14 UTC Re: Turning Spindle Off and On Fred Smith 2004-12-16 19:39:02 UTC Re: Turning Spindle Off and On JamesCullins 2004-12-16 19:52:26 UTC Re: [CAD_CAM_EDM_DRO] Re: Turning Spindle Off and On turbulatordude 2004-12-16 23:01:08 UTC Re: Turning Spindle Off and On kadeshan 2004-12-17 08:28:34 UTC Re: Turning Spindle Off and On R Rogers 2004-12-17 08:39:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Turning Spindle Off and On Kim Lux 2004-12-17 08:46:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Turning Spindle Off and On kadeshan 2004-12-17 09:14:28 UTC Re: Turning Spindle Off and On turbulatordude 2004-12-17 09:34:11 UTC Re: Turning Spindle Off and On - wiring to the VSD Kim Lux 2004-12-17 10:00:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Turning Spindle Off and On Peter Homann 2004-12-17 15:10:15 UTC Re: [CAD_CAM_EDM_DRO] Turning Spindle Off and On Fred Smith 2004-12-17 15:26:11 UTC Re: Turning Spindle Off and On