Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Posted by
Stephen Wille Padnos
on 2005-01-03 07:47:11 UTC
R Rogers wrote:
[snip]
The G320 and the G340 have the same internal limitation of 250KHz
(250,000 counts per second). Note that that's per second, not per
minute - this is 15 million pulses per minute. A 1000-CPR (4000 PPR in
quadrature) encoder can spin at 3750 RPM before you hit that speed limit.
The pulse multiplier doesn't increase the maximum rate that can be
achieved, it reduces the step rate necessary to achieve a particular
speed. That allows software based step generators (EMC, Mach2, Ah-Ha,
etc) to get faster speeds with their limited step output rates.
Something like Jon Elson's USC can output 300K step pulses per second,
so that wouldn't require a G340 even at full speed.
- Steve
[rest of thread snipped]
[snip]
>Encoder resolution? The G320 has a max pulse rate of 250 quadrature. Any resolution above 1000 CPR would require the G340 with step multiplier.This isn't quite right.
>
The G320 and the G340 have the same internal limitation of 250KHz
(250,000 counts per second). Note that that's per second, not per
minute - this is 15 million pulses per minute. A 1000-CPR (4000 PPR in
quadrature) encoder can spin at 3750 RPM before you hit that speed limit.
The pulse multiplier doesn't increase the maximum rate that can be
achieved, it reduces the step rate necessary to achieve a particular
speed. That allows software based step generators (EMC, Mach2, Ah-Ha,
etc) to get faster speeds with their limited step output rates.
Something like Jon Elson's USC can output 300K step pulses per second,
so that wouldn't require a G340 even at full speed.
- Steve
[rest of thread snipped]
Discussion Thread
mmurray701
2005-01-01 21:59:47 UTC
Loosing position and need help...
Joel
2005-01-02 06:38:20 UTC
Re: Loosing position and need help...
A. G. Eckstein
2005-01-02 06:48:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Randy Wink
2005-01-02 07:54:27 UTC
RE: [CAD_CAM_EDM_DRO] Loosing position and need help...
R Rogers
2005-01-02 14:11:58 UTC
Re: [CAD_CAM_EDM_DRO] Loosing position and need help...
mmurray701
2005-01-02 19:23:13 UTC
Re: Loosing position and need help...
Jon Elson
2005-01-02 19:47:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Gary
2005-01-03 00:20:04 UTC
Re: Loosing position and need help...
R Rogers
2005-01-03 06:44:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
A. G. Eckstein
2005-01-03 07:16:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Stephen Wille Padnos
2005-01-03 07:47:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
R Rogers
2005-01-03 13:15:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Torsten
2005-01-03 14:37:56 UTC
Re: Loosing position and need help...
Steve Stallings
2005-01-03 14:50:54 UTC
Re: Loosing position and need help...
David Paulson
2005-01-03 15:25:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
mmurray701
2005-01-03 19:23:58 UTC
Re: Loosing position and need help...
Jon Elson
2005-01-03 21:03:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Torsten
2005-01-04 01:50:18 UTC
Re: Loosing position and need help...
Henrik Olsson
2005-01-04 10:21:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...