Re: Loosing position and need help...
Posted by
Steve Stallings
on 2005-01-03 14:50:54 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Torsten" <torsten@g...>
wrote:
products is a voltage controlled oscillator that creates
multiple output pulses for a single input pulse. They
can be set for 2X, 5X, or 10X multiply. The 340 does not
divide the encoder input. This keeps the gain and
resolution high while reducing the required input
pulse frequency.
Regards,
Steve Stallings
wrote:
>Because, it really does multiply. The multiplier in Gecko
> For a long time I was been very confused about
> the difference between a G320 and G340 so if
> I understand this right the G320 works with
> the encoder resolution as is and the G340 actualy
> divides this resolution to require lower pulse rates
> from the computer.
> Is the G340 adjustable for different division ratios?
> Why call this a multiplier when what it dose is divide?
>
products is a voltage controlled oscillator that creates
multiple output pulses for a single input pulse. They
can be set for 2X, 5X, or 10X multiply. The 340 does not
divide the encoder input. This keeps the gain and
resolution high while reducing the required input
pulse frequency.
Regards,
Steve Stallings
Discussion Thread
mmurray701
2005-01-01 21:59:47 UTC
Loosing position and need help...
Joel
2005-01-02 06:38:20 UTC
Re: Loosing position and need help...
A. G. Eckstein
2005-01-02 06:48:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Randy Wink
2005-01-02 07:54:27 UTC
RE: [CAD_CAM_EDM_DRO] Loosing position and need help...
R Rogers
2005-01-02 14:11:58 UTC
Re: [CAD_CAM_EDM_DRO] Loosing position and need help...
mmurray701
2005-01-02 19:23:13 UTC
Re: Loosing position and need help...
Jon Elson
2005-01-02 19:47:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Gary
2005-01-03 00:20:04 UTC
Re: Loosing position and need help...
R Rogers
2005-01-03 06:44:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
A. G. Eckstein
2005-01-03 07:16:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Stephen Wille Padnos
2005-01-03 07:47:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
R Rogers
2005-01-03 13:15:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Torsten
2005-01-03 14:37:56 UTC
Re: Loosing position and need help...
Steve Stallings
2005-01-03 14:50:54 UTC
Re: Loosing position and need help...
David Paulson
2005-01-03 15:25:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
mmurray701
2005-01-03 19:23:58 UTC
Re: Loosing position and need help...
Jon Elson
2005-01-03 21:03:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...
Torsten
2005-01-04 01:50:18 UTC
Re: Loosing position and need help...
Henrik Olsson
2005-01-04 10:21:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Loosing position and need help...