Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase
Posted by
cnc002@a...
on 2005-04-19 12:58:00 UTC
In a message dated 4/19/2005 2:50:32 PM Eastern Standard Time,
polaraligned@... writes:
A motor rewinder I talked to said that 3600 RPM is the desired
rated speed for a converter. Any truth to this?
And what horsepower rating should I get to run a BOSS 2HP mill?
Thanks,
Scott
Scott:
3600 is pretty much a standard speed for a 60Hz AC motor. And as far as the
size of converter you need for a 2Hp mill. Unless you have a lot of other
motors on there then a 3 to 5 Hp would be more than sufficient. You have to
be careful not to go too big or the converter will simply not work properly.
Also, I know there are a lot of static three phase converters out there but
you would be well advised to go with a rotary phase convertor. They generate
an output much closer to true three phase than does a static unit. Also,
remember to always start the LARGEST motor on your machine FIRST then the
smaller ones afterwards. You will have a lot fewer problems if you do this.
Hope this helps.
Randy Abernathy
4626 Old Stilesboro Road
Acworth, GA 30101
Ph / Fax: 770-974-5295
E-mail: cnc002@...
I furnish technical support, repair, and other related services for your
industrial woodworking machinery. My background as Senior Service Engineer for
the SCMI Group for nearly fifteen years with factory training, combines with
my extensive background in electronics, mechanics, pneumatics, electrical and
CNC machinery to offer you needed support for your machinery.
[Non-text portions of this message have been removed]
polaraligned@... writes:
A motor rewinder I talked to said that 3600 RPM is the desired
rated speed for a converter. Any truth to this?
And what horsepower rating should I get to run a BOSS 2HP mill?
Thanks,
Scott
Scott:
3600 is pretty much a standard speed for a 60Hz AC motor. And as far as the
size of converter you need for a 2Hp mill. Unless you have a lot of other
motors on there then a 3 to 5 Hp would be more than sufficient. You have to
be careful not to go too big or the converter will simply not work properly.
Also, I know there are a lot of static three phase converters out there but
you would be well advised to go with a rotary phase convertor. They generate
an output much closer to true three phase than does a static unit. Also,
remember to always start the LARGEST motor on your machine FIRST then the
smaller ones afterwards. You will have a lot fewer problems if you do this.
Hope this helps.
Randy Abernathy
4626 Old Stilesboro Road
Acworth, GA 30101
Ph / Fax: 770-974-5295
E-mail: cnc002@...
I furnish technical support, repair, and other related services for your
industrial woodworking machinery. My background as Senior Service Engineer for
the SCMI Group for nearly fifteen years with factory training, combines with
my extensive background in electronics, mechanics, pneumatics, electrical and
CNC machinery to offer you needed support for your machinery.
[Non-text portions of this message have been removed]
Discussion Thread
Polaraligned
2005-04-18 13:55:10 UTC
Running a BOSS on single phase
Doug Fortune
2005-04-18 15:20:18 UTC
Re: Running a BOSS on single phase
Jon Elson
2005-04-18 19:39:19 UTC
Re: [CAD_CAM_EDM_DRO] Running a BOSS on single phase
Jon Elson
2005-04-18 19:42:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase
JanRwl@A...
2005-04-18 21:25:50 UTC
Re: [CAD_CAM_EDM_DRO] Running a BOSS on single phase
Polaraligned
2005-04-19 02:52:37 UTC
Re: Running a BOSS on single phase
Polaraligned
2005-04-19 04:10:34 UTC
Re: Running a BOSS on single phase
Jon Elson
2005-04-19 09:07:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase
Jon Elson
2005-04-19 09:09:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase
turbulatordude
2005-04-19 09:55:02 UTC
Re: Running a BOSS on single phase
Polaraligned
2005-04-19 11:41:23 UTC
Re: Running a BOSS on single phase
cnc002@a...
2005-04-19 12:58:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase
ballendo
2005-04-19 15:42:30 UTC
Re: Running a BOSS on single phase
cnc002@a...
2005-04-20 18:05:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase
cnc_4_me
2005-04-20 21:00:55 UTC
Re: Running a BOSS on single phase
Doug Fortune
2005-04-20 22:42:25 UTC
Haas mini "Office Lathe" and mini "Office Mill"
Les Newell
2005-04-20 23:38:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase
Polaraligned
2005-04-21 04:10:22 UTC
Re: Running a BOSS on single phase
washcomp
2005-04-21 04:21:58 UTC
Re: Running a BOSS on single phase
Les Newell
2005-04-21 06:51:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase
Doug Fortune
2005-04-21 08:29:35 UTC
Re: Running a BOSS on single phase
vavaroutsos
2005-04-21 15:39:39 UTC
Re: Running a BOSS on single phase
Polaraligned
2005-04-22 04:25:55 UTC
Anyone Convert BOSS to servo's?
Les Newell
2005-04-22 05:19:44 UTC
Re: [CAD_CAM_EDM_DRO] Anyone Convert BOSS to servo's?
Polaraligned
2005-04-22 15:56:47 UTC
Re: Anyone Convert BOSS to servo's?
Les Newell
2005-04-25 01:19:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Anyone Convert BOSS to servo's?
Polaraligned
2005-04-26 03:40:52 UTC
BOSS to servo's and reduction
R Rogers
2005-04-26 06:16:18 UTC
Re: [CAD_CAM_EDM_DRO] BOSS to servo's and reduction
Polaraligned
2005-04-26 17:59:51 UTC
Re: BOSS to servo's and reduction
R Rogers
2005-04-26 19:00:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS to servo's and reduction
Les Newell
2005-04-27 02:05:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS to servo's and reduction
Polaraligned
2005-04-27 05:47:59 UTC
Re: BOSS to servo's and reduction
R Rogers
2005-04-27 06:54:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS to servo's and reduction
Polaraligned
2005-04-27 10:46:14 UTC
Re: BOSS to servo's and reduction