CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: BOSS to servo's and reduction

Posted by Les Newell
on 2005-04-27 02:05:35 UTC
Hi Scott,

Boring the pulley out should work. I have done it before and used two
grub screws at 90 degrees to hold the pulley. If you are worried about
it coming loose then a small amount of ordinary loctite thread locker
will hold it firmly in place. It will still be removeable with the
application of a bit of heat to soften the loctite.

Les


Polaraligned wrote:

>
>Ron,
>
>I need to use the HTD 5mm pitch belts. It seems to be the only
>series that can fit in the BOSS, and get the reduction I need. 3-3/4"
>is about the largest I can go on the secondary pulley. I like your
>idea about using a roll pin to fasten the pulley. The primary pulley
>I need to use has a .63" hub and is just .907" outside diameter. I
>wonder how well
>it would work if I just bored .625 hole and used a pin. The pulley
>would get quite thin (1/4") but maybe there is an adhesive I could use
>to bond it to the shaft along with the pin. Make it like part of the
>shaft. Any thoughts?
>
>Thanks,
>Scott
>
>
>

Discussion Thread

Polaraligned 2005-04-18 13:55:10 UTC Running a BOSS on single phase Doug Fortune 2005-04-18 15:20:18 UTC Re: Running a BOSS on single phase Jon Elson 2005-04-18 19:39:19 UTC Re: [CAD_CAM_EDM_DRO] Running a BOSS on single phase Jon Elson 2005-04-18 19:42:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase JanRwl@A... 2005-04-18 21:25:50 UTC Re: [CAD_CAM_EDM_DRO] Running a BOSS on single phase Polaraligned 2005-04-19 02:52:37 UTC Re: Running a BOSS on single phase Polaraligned 2005-04-19 04:10:34 UTC Re: Running a BOSS on single phase Jon Elson 2005-04-19 09:07:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase Jon Elson 2005-04-19 09:09:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase turbulatordude 2005-04-19 09:55:02 UTC Re: Running a BOSS on single phase Polaraligned 2005-04-19 11:41:23 UTC Re: Running a BOSS on single phase cnc002@a... 2005-04-19 12:58:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase ballendo 2005-04-19 15:42:30 UTC Re: Running a BOSS on single phase cnc002@a... 2005-04-20 18:05:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase cnc_4_me 2005-04-20 21:00:55 UTC Re: Running a BOSS on single phase Doug Fortune 2005-04-20 22:42:25 UTC Haas mini "Office Lathe" and mini "Office Mill" Les Newell 2005-04-20 23:38:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase Polaraligned 2005-04-21 04:10:22 UTC Re: Running a BOSS on single phase washcomp 2005-04-21 04:21:58 UTC Re: Running a BOSS on single phase Les Newell 2005-04-21 06:51:26 UTC Re: [CAD_CAM_EDM_DRO] Re: Running a BOSS on single phase Doug Fortune 2005-04-21 08:29:35 UTC Re: Running a BOSS on single phase vavaroutsos 2005-04-21 15:39:39 UTC Re: Running a BOSS on single phase Polaraligned 2005-04-22 04:25:55 UTC Anyone Convert BOSS to servo's? Les Newell 2005-04-22 05:19:44 UTC Re: [CAD_CAM_EDM_DRO] Anyone Convert BOSS to servo's? Polaraligned 2005-04-22 15:56:47 UTC Re: Anyone Convert BOSS to servo's? Les Newell 2005-04-25 01:19:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Anyone Convert BOSS to servo's? Polaraligned 2005-04-26 03:40:52 UTC BOSS to servo's and reduction R Rogers 2005-04-26 06:16:18 UTC Re: [CAD_CAM_EDM_DRO] BOSS to servo's and reduction Polaraligned 2005-04-26 17:59:51 UTC Re: BOSS to servo's and reduction R Rogers 2005-04-26 19:00:49 UTC Re: [CAD_CAM_EDM_DRO] Re: BOSS to servo's and reduction Les Newell 2005-04-27 02:05:35 UTC Re: [CAD_CAM_EDM_DRO] Re: BOSS to servo's and reduction Polaraligned 2005-04-27 05:47:59 UTC Re: BOSS to servo's and reduction R Rogers 2005-04-27 06:54:21 UTC Re: [CAD_CAM_EDM_DRO] Re: BOSS to servo's and reduction Polaraligned 2005-04-27 10:46:14 UTC Re: BOSS to servo's and reduction