Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One?
Posted by
Luke1027
on 2005-04-30 17:07:36 UTC
Ignorance here on voltage/amps for RPM.
What exactly do I need to consider if I am running
bipolar steppers? If I put more voltage to the motor
will that increase the amperage? I assume yes...
but is this linear? 20% more voltage would mean
20% more amerage? Which in turn would up my RPM...
by what? Any rule of thumb here?
Thanks,
Luke
Monte wrote:
What exactly do I need to consider if I am running
bipolar steppers? If I put more voltage to the motor
will that increase the amperage? I assume yes...
but is this linear? 20% more voltage would mean
20% more amerage? Which in turn would up my RPM...
by what? Any rule of thumb here?
Thanks,
Luke
Monte wrote:
>
>They are both good drives, but the Gecko's will allow you a higher
>voltage to drive your motors. If you can get by with 28vdc the
>Xylotex would work. If you need more (up to 80vdc) the Gecko's would
>be worth looking at. The Gecko's will cost a bit more. I have a
>Xylotex and can get 40ipm rapids on a Taig mill with 28vdc power
>supply and 258 oz-in steppers and Mach2.
>
>Monte
>
>
>
>
Discussion Thread
Luke1027
2005-04-29 19:00:59 UTC
[CAD_CAM_EDM_DRO] MircoStepping Drive Which One?
Robert Campbell
2005-04-29 19:09:26 UTC
Re: [CAD_CAM_EDM_DRO] MircoStepping Drive Which One?
Monte
2005-04-29 20:49:01 UTC
Re: MircoStepping Drive Which One?
turbulatordude
2005-04-29 23:03:03 UTC
Re: MircoStepping Drive Which One?
Fred Smith
2005-04-30 07:29:37 UTC
Re: MircoStepping Drive Which One?
Monte
2005-04-30 08:03:42 UTC
Re: MircoStepping Drive Which One?
turbulatordude
2005-04-30 08:28:35 UTC
Re: MircoStepping Drive Which One?
caudlet
2005-04-30 12:26:15 UTC
Re: MircoStepping Drive Which One?
Fred Smith
2005-04-30 13:10:30 UTC
Re: MircoStepping Drive Which One?
Steve Stallings
2005-04-30 14:09:09 UTC
Re: MircoStepping Drive Which One?
Luke1027
2005-04-30 17:07:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One?
Luke1027
2005-04-30 17:07:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One?
Luke1027
2005-04-30 17:07:52 UTC
[CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One?
caudlet
2005-04-30 17:08:15 UTC
Re: MircoStepping Drive Which One?
turbulatordude
2005-05-01 07:09:28 UTC
Re: MircoStepping Drive Which One? ARCSIN or serovs ?
turbulatordude
2005-05-01 07:35:05 UTC
Re: MircoStepping Drive Which One? Servo's
John Meissner
2005-05-01 10:38:51 UTC
Re: MircoStepping Drive Which One? Servo's
turbulatordude
2005-05-01 11:24:13 UTC
Re: MircoStepping Drive Which One? Servo's
Randy Wink
2005-05-01 12:17:13 UTC
RE: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? Servo's
Fred Smith
2005-05-01 15:07:24 UTC
Re: MircoStepping Drive Which One? Servo's
Les Newell
2005-05-01 17:03:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? Servo's
Mariss Freimanis
2005-05-01 17:28:37 UTC
Re: MircoStepping Drive Which One?
turbulatordude
2005-05-01 19:30:49 UTC
Re: Servo's and surplus center encoder
Fred Smith
2005-05-03 05:05:26 UTC
Re: MircoStepping Drive Which One? Servo's