CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One?

Posted by Luke1027
on 2005-04-30 17:07:47 UTC
Yes I was planning on running twin leadscrews.
But I do have a questions about this ... that is,
would one of these motors be consider a Slave drive?
If so, then the

http://www.buildyouridea.com/hardware/arcsin/arcsin.html
driver (3 axes) would be able to be used?


Arcsin features:

* Ribbon cable connector for additional slave driver when 2 motors
are needed for a single axis.


Luke


turbulatordude wrote:

>Although the Xylotex is a decent drive it has it's limits to motor size.
>
>The HobbyCNC board is a 3 axis board, not sure why you want 4 axis with
>plasma unless you plan on running twin leadscrews.
>
>
>

Discussion Thread

Luke1027 2005-04-29 19:00:59 UTC [CAD_CAM_EDM_DRO] MircoStepping Drive Which One? Robert Campbell 2005-04-29 19:09:26 UTC Re: [CAD_CAM_EDM_DRO] MircoStepping Drive Which One? Monte 2005-04-29 20:49:01 UTC Re: MircoStepping Drive Which One? turbulatordude 2005-04-29 23:03:03 UTC Re: MircoStepping Drive Which One? Fred Smith 2005-04-30 07:29:37 UTC Re: MircoStepping Drive Which One? Monte 2005-04-30 08:03:42 UTC Re: MircoStepping Drive Which One? turbulatordude 2005-04-30 08:28:35 UTC Re: MircoStepping Drive Which One? caudlet 2005-04-30 12:26:15 UTC Re: MircoStepping Drive Which One? Fred Smith 2005-04-30 13:10:30 UTC Re: MircoStepping Drive Which One? Steve Stallings 2005-04-30 14:09:09 UTC Re: MircoStepping Drive Which One? Luke1027 2005-04-30 17:07:36 UTC Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? Luke1027 2005-04-30 17:07:47 UTC Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? Luke1027 2005-04-30 17:07:52 UTC [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? caudlet 2005-04-30 17:08:15 UTC Re: MircoStepping Drive Which One? turbulatordude 2005-05-01 07:09:28 UTC Re: MircoStepping Drive Which One? ARCSIN or serovs ? turbulatordude 2005-05-01 07:35:05 UTC Re: MircoStepping Drive Which One? Servo's John Meissner 2005-05-01 10:38:51 UTC Re: MircoStepping Drive Which One? Servo's turbulatordude 2005-05-01 11:24:13 UTC Re: MircoStepping Drive Which One? Servo's Randy Wink 2005-05-01 12:17:13 UTC RE: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? Servo's Fred Smith 2005-05-01 15:07:24 UTC Re: MircoStepping Drive Which One? Servo's Les Newell 2005-05-01 17:03:42 UTC Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? Servo's Mariss Freimanis 2005-05-01 17:28:37 UTC Re: MircoStepping Drive Which One? turbulatordude 2005-05-01 19:30:49 UTC Re: Servo's and surplus center encoder Fred Smith 2005-05-03 05:05:26 UTC Re: MircoStepping Drive Which One? Servo's