Re: Servo's and surplus center encoder
Posted by
turbulatordude
on 2005-05-01 19:30:49 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Randy Wink" <rwwink@i...>
wrote:
The motor is rated for 24 volts (good) but 0.1 amp. (Bad)
even an old nema23 motor from the old printers will have more umph.
This is 2.4 watts of power.
A 1-1/2 inch dia and 4" long overall, the unit is a toy.
1hp = 746 watts.
1 treadmill motor = 1-1/2 hp
an old NEMA23, round body will have around 5 watts so these are very
small motors indeed.
Dave
wrote:
> Just a question...screw (5
> If, instead of tossing the motor, I used it. Using a .200 lead
> turns per inch) and turning it @ 500 RPM to get 100 inches perminute, I'd
> need a 7.8:1 ratio between the motor and the screw to gear it downto that
> speed full out. That would be a big multiplier for whatever torquethe
> motor could put out and also give me something like 1440 encoderpulses per
> rev. Am I missing something in this?Yes.
> R. Wink
The motor is rated for 24 volts (good) but 0.1 amp. (Bad)
even an old nema23 motor from the old printers will have more umph.
This is 2.4 watts of power.
A 1-1/2 inch dia and 4" long overall, the unit is a toy.
1hp = 746 watts.
1 treadmill motor = 1-1/2 hp
an old NEMA23, round body will have around 5 watts so these are very
small motors indeed.
Dave
Discussion Thread
Luke1027
2005-04-29 19:00:59 UTC
[CAD_CAM_EDM_DRO] MircoStepping Drive Which One?
Robert Campbell
2005-04-29 19:09:26 UTC
Re: [CAD_CAM_EDM_DRO] MircoStepping Drive Which One?
Monte
2005-04-29 20:49:01 UTC
Re: MircoStepping Drive Which One?
turbulatordude
2005-04-29 23:03:03 UTC
Re: MircoStepping Drive Which One?
Fred Smith
2005-04-30 07:29:37 UTC
Re: MircoStepping Drive Which One?
Monte
2005-04-30 08:03:42 UTC
Re: MircoStepping Drive Which One?
turbulatordude
2005-04-30 08:28:35 UTC
Re: MircoStepping Drive Which One?
caudlet
2005-04-30 12:26:15 UTC
Re: MircoStepping Drive Which One?
Fred Smith
2005-04-30 13:10:30 UTC
Re: MircoStepping Drive Which One?
Steve Stallings
2005-04-30 14:09:09 UTC
Re: MircoStepping Drive Which One?
Luke1027
2005-04-30 17:07:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One?
Luke1027
2005-04-30 17:07:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One?
Luke1027
2005-04-30 17:07:52 UTC
[CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One?
caudlet
2005-04-30 17:08:15 UTC
Re: MircoStepping Drive Which One?
turbulatordude
2005-05-01 07:09:28 UTC
Re: MircoStepping Drive Which One? ARCSIN or serovs ?
turbulatordude
2005-05-01 07:35:05 UTC
Re: MircoStepping Drive Which One? Servo's
John Meissner
2005-05-01 10:38:51 UTC
Re: MircoStepping Drive Which One? Servo's
turbulatordude
2005-05-01 11:24:13 UTC
Re: MircoStepping Drive Which One? Servo's
Randy Wink
2005-05-01 12:17:13 UTC
RE: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? Servo's
Fred Smith
2005-05-01 15:07:24 UTC
Re: MircoStepping Drive Which One? Servo's
Les Newell
2005-05-01 17:03:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: MircoStepping Drive Which One? Servo's
Mariss Freimanis
2005-05-01 17:28:37 UTC
Re: MircoStepping Drive Which One?
turbulatordude
2005-05-01 19:30:49 UTC
Re: Servo's and surplus center encoder
Fred Smith
2005-05-03 05:05:26 UTC
Re: MircoStepping Drive Which One? Servo's