Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Posted by
Alan Marconett
on 2006-01-21 17:00:11 UTC
Andy,
Haven't you brought this up before? TOO picky! And I said oz/in!
Google searches for each way are about the same.
Let's see if we can figure out this guy's problem!
Alan KM6VV
Andy Wander wrote:
Haven't you brought this up before? TOO picky! And I said oz/in!
Google searches for each way are about the same.
Let's see if we can figure out this guy's problem!
Alan KM6VV
Andy Wander wrote:
> "picayune mode on"
>
> It's oz-in, NOT oz/inch.
>
> "picayune mode off"
>
>
> Andy Wander
>
>
> Hi Mike,
>
> NEW-OLD STOCK? I'm guessing that there's nothing wrong with them. Just
> connect up an appropriate driver to them, and they'll work fine! 700
> oz/in is BIG!
>
> You could make an ohm-meter check on the windings. We don't want to fry
> a driver, in case a winding is shorted.
>
> Alan KM6VV
>
Discussion Thread
iseechipsfly
2006-01-21 08:18:04 UTC
Frozen stepper motor shaft
JanRwl@A...
2006-01-21 13:52:02 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Alan Marconett
2006-01-21 14:00:24 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Jon Elson
2006-01-21 15:02:09 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Andy Wander
2006-01-21 15:14:46 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
R Rogers
2006-01-21 16:56:49 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Alan Marconett
2006-01-21 17:00:11 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Andy Wander
2006-01-21 18:21:56 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Alan Marconett
2006-01-21 18:36:39 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Andy Wander
2006-01-21 18:42:54 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
JanRwl@A...
2006-01-21 20:08:30 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
iseechipsfly
2006-01-21 20:15:18 UTC
Re: Frozen stepper motor shaft
Stephen Wille Padnos
2006-01-21 20:32:59 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
iseechipsfly
2006-01-21 20:43:52 UTC
Re: Frozen stepper motor shaft
Bill Yates
2006-01-22 03:40:58 UTC
Re: Frozen stepper motor shaft
Mariss Freimanis
2006-01-22 08:39:06 UTC
Re: Frozen stepper motor shaft
Jarrett & Heidi Johnson
2006-01-22 10:54:50 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Andy Wander
2006-01-22 11:15:44 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Jarrett & Heidi Johnson
2006-01-22 11:29:56 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Dan Mauch
2006-01-22 11:35:33 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Alan Marconett
2006-01-22 14:04:53 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
wthomas@g...
2006-01-22 14:18:02 UTC
W.E.T.[CAD_CAM_EDM_DRO] Torque, Force, or Work