CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft

on 2006-01-22 14:04:53 UTC
Hi Steve,

And by the same token, a '/' is not always a division sign. When I
write step/dir, I obviously don't want the reader to divide! Which is
better? I'd say there is room for both!

But hay, I'm flexible, I no longer write MC (Mega Cycles), when everyone
else writes MHz!

Alan KM6VV

Stephen Wille Padnos wrote:
> Alan Marconett wrote:
>
>
>>Hi Andy,
>>
>>I agree that it's not oz divided by inches, but it's not oz MINUS inches
>>either! I'll probably be OK when it comes to the equations. Each to
>>his/her own! ;>)
>>
>>
>
> Don't think of it in mathematical terms, think of it in grammatical
> terms. You're making a compound word from "ounce" and "inch", so you
> hyphenate. These aren't mathematical symbols when used in sentences.
>
> Often, if people want to keep the units straight in an equation, they
> end up writing oz*in anyway.
>
> - Steve
>

Discussion Thread

iseechipsfly 2006-01-21 08:18:04 UTC Frozen stepper motor shaft JanRwl@A... 2006-01-21 13:52:02 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Alan Marconett 2006-01-21 14:00:24 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Jon Elson 2006-01-21 15:02:09 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Andy Wander 2006-01-21 15:14:46 UTC RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft R Rogers 2006-01-21 16:56:49 UTC RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Alan Marconett 2006-01-21 17:00:11 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Andy Wander 2006-01-21 18:21:56 UTC RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Alan Marconett 2006-01-21 18:36:39 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Andy Wander 2006-01-21 18:42:54 UTC RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft JanRwl@A... 2006-01-21 20:08:30 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft iseechipsfly 2006-01-21 20:15:18 UTC Re: Frozen stepper motor shaft Stephen Wille Padnos 2006-01-21 20:32:59 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft iseechipsfly 2006-01-21 20:43:52 UTC Re: Frozen stepper motor shaft Bill Yates 2006-01-22 03:40:58 UTC Re: Frozen stepper motor shaft Mariss Freimanis 2006-01-22 08:39:06 UTC Re: Frozen stepper motor shaft Jarrett & Heidi Johnson 2006-01-22 10:54:50 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Andy Wander 2006-01-22 11:15:44 UTC RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Jarrett & Heidi Johnson 2006-01-22 11:29:56 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Dan Mauch 2006-01-22 11:35:33 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft Alan Marconett 2006-01-22 14:04:53 UTC Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft wthomas@g... 2006-01-22 14:18:02 UTC W.E.T.[CAD_CAM_EDM_DRO] Torque, Force, or Work