Re: Frozen stepper motor shaft
Posted by
iseechipsfly
on 2006-01-21 20:15:18 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Andy Wander" <awander@v...>
wrote:
steppers, but you never know, right). The corrosion was not apparent
on casual inspection, as it was pretty much confined to the part of
the shaft INSIDE the bearings.
Each to his/her own! ;>)
pretty good steel, I've seldom (if ever?) seen any rust there. Bent
shaft, dented end bells (different name?) as others have mentioned,
would also be serious. But I just took it that they were new/used,
and might actually be OK (hope so!).
wrote:
>talking "ounce-force", huh............?
> ...I guess if I'm going to be so pedantic I should be
>along the shaft, and froze things up. (the ones I saw were not
> I have seen motors that got wet in storage, where water seeped in
steppers, but you never know, right). The corrosion was not apparent
on casual inspection, as it was pretty much confined to the part of
the shaft INSIDE the bearings.
>[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Alan Marconett
> Andy Wander
> Verrex Corporation
>
> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> Sent: Saturday, January 21, 2006 9:35 PMinches either! I'll probably be OK when it comes to the equations.
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
>
> Hi Andy,
>
> I agree that it's not oz divided by inches, but it's not oz MINUS
Each to his/her own! ;>)
>serious problem! The shafts I've seen on steppers seem to be of a
> The RUST on the shaft/end bells would surely be an indication of a
pretty good steel, I've seldom (if ever?) seen any rust there. Bent
shaft, dented end bells (different name?) as others have mentioned,
would also be serious. But I just took it that they were new/used,
and might actually be OK (hope so!).
>
> Alan KM6VV
> Déjà Vu!
>
>
>
> This communication including any attachments, are intended
> for the exclusive use of the addressee(s) and contains
> confidential or copyrighted materials. Duplication,
> distribution or reproduction is strictly prohibited by law
> without written permission of Verrex
>
Discussion Thread
iseechipsfly
2006-01-21 08:18:04 UTC
Frozen stepper motor shaft
JanRwl@A...
2006-01-21 13:52:02 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Alan Marconett
2006-01-21 14:00:24 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Jon Elson
2006-01-21 15:02:09 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Andy Wander
2006-01-21 15:14:46 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
R Rogers
2006-01-21 16:56:49 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Alan Marconett
2006-01-21 17:00:11 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Andy Wander
2006-01-21 18:21:56 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Alan Marconett
2006-01-21 18:36:39 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Andy Wander
2006-01-21 18:42:54 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
JanRwl@A...
2006-01-21 20:08:30 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
iseechipsfly
2006-01-21 20:15:18 UTC
Re: Frozen stepper motor shaft
Stephen Wille Padnos
2006-01-21 20:32:59 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
iseechipsfly
2006-01-21 20:43:52 UTC
Re: Frozen stepper motor shaft
Bill Yates
2006-01-22 03:40:58 UTC
Re: Frozen stepper motor shaft
Mariss Freimanis
2006-01-22 08:39:06 UTC
Re: Frozen stepper motor shaft
Jarrett & Heidi Johnson
2006-01-22 10:54:50 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Andy Wander
2006-01-22 11:15:44 UTC
RE: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Jarrett & Heidi Johnson
2006-01-22 11:29:56 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Dan Mauch
2006-01-22 11:35:33 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
Alan Marconett
2006-01-22 14:04:53 UTC
Re: [CAD_CAM_EDM_DRO] Frozen stepper motor shaft
wthomas@g...
2006-01-22 14:18:02 UTC
W.E.T.[CAD_CAM_EDM_DRO] Torque, Force, or Work