CAD CAM EDM DRO - Yahoo Group Archive

Re: dxf to gcode to Galil DMC software

Posted by geostabilizer
on 2006-01-30 19:39:55 UTC
Opps!!
Just discovered a Galil driver conflict is generated when
installing the previously announced gdmc demo program onto a Win
2000 platform. So if you are installing on a machine with a working
Galil controller PLEASE hold off installing the gdmc application
unless you are an expert at installing Galil device drivers (hint:
the Gilil dmcdriverdll02.exe Ver. 7 DMC Driver (
http://66.60.181.132/xnet/checkreg.aspxlocation=software&target=dmcdr
iverdll02 ) needs to be reinstalled after gdmc is installed). If
previous link does not work then try at:
http://www.galilmc.com/support/download.html

Ignore this message if you still want to install the program just to
check out the GUI or dxf to gcode conversion.
Sorry for the inconvenience and hope to be posting that I have a
remedy for this problem soon.

I am anxious to find out if any one else out there is using one of
the "over 350000 worldwide installed controllers" Galil claims to
have out there in the market place.

Thanks, George


--- In CAD_CAM_EDM_DRO@yahoogroups.com, "geostabilizer"
<gmalone@w...> wrote:
>
> Announcement: Galil controller software demo.
>
> After many hours of designing and testing I have finally developed
a
> 4-azis motion controller program application, called gdmc, that
does
> adequate commanding of a Galil DMC18xx PCI based servo controller
> card. I use for it for 100 watt CO2 laser cutting and etching
> projects. Not too long ago it could only convert VisualMill
> generated gcode files into the appropriate DMC commands. Now it
can
> do processing of dxf drawing files directly. (However, the dxf
> importing filter has lots of growing pains at the moment so please
> forgive it's idiosyncrasies ).
> If you choose to check out gdmc you will be presented with a GUI
> that has lots of buttons, dials, displays, widgets, etc., and the
> best way to learn the ins and outs of gdmc is to "play" with all
the
> buttons. It was going to have a National Instruments LabVIEW
> interface someday and thus it looks and feels a little LabVIEW'ish.
>
> I am presenting gdmc to CAD_CAM_EDM_DRO audience in hopes of
finding
> others that would have an interest in its further development. The
> CAM application is in the early stages of beta development. It is
a
> use full and unique tool for me to use and its time to find out if
> any one else out there listing to the world wide web could get
some
> benefit out of the program too. Of course you would need Galil DMC
> 18xx PCI controller board to control a laser or router.
>
> http://www.goldtreesystems.com/testing.htm
>
> You may contact me directly for instillation and operating
> assistance.
>
> Cheers, George
>

Discussion Thread

geostabilizer 2006-01-30 16:42:53 UTC dxf to gcode to Galil DMC software geostabilizer 2006-01-30 19:38:37 UTC Re: dxf to gcode to Galil DMC software geostabilizer 2006-01-30 19:39:55 UTC Re: dxf to gcode to Galil DMC software Brad 2006-01-31 15:14:49 UTC Re: dxf to gcode to Galil DMC software geostabilizer 2006-02-01 13:35:00 UTC Re: dxf to gcode to Galil DMC software Shawncd 2006-02-01 17:37:23 UTC Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software Shawncd 2006-02-01 17:38:21 UTC Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software Shawncd 2006-02-01 17:46:19 UTC Re: dxf to gcode to Galil DMC software geostabilizer 2006-02-01 19:30:32 UTC Re: dxf to gcode to Galil DMC software shawncd@p... 2006-02-02 11:20:59 UTC Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software geostabilizer 2006-02-06 07:25:23 UTC Re: dxf to gcode to Galil DMC software shawncd@p... 2006-02-06 11:02:55 UTC Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software Shawncd 2006-02-07 19:29:04 UTC Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software geostabilizer 2006-02-08 09:57:59 UTC Re: dxf to gcode to Galil DMC software GutZ 2010-12-22 05:44:26 UTC Re: dxf to gcode to Galil DMC software