Re: dxf to gcode to Galil DMC software
Posted by
geostabilizer
on 2006-02-06 07:25:23 UTC
Hi Shawn,
I checked galilmc.com and could not find any info on the 730
controller. I suspect it is not a "bus-based" type. If it is the
stand alone RS-232 type of interface my software should still be
able to communicate with it using the Windows drivers however the
real-time controller status may be too slow for the purpose of
controller the laser. I would like to know more about this card. Do
you have a pdf users manual you could email?
Thanks, George
I checked galilmc.com and could not find any info on the 730
controller. I suspect it is not a "bus-based" type. If it is the
stand alone RS-232 type of interface my software should still be
able to communicate with it using the Windows drivers however the
real-time controller status may be too slow for the purpose of
controller the laser. I would like to know more about this card. Do
you have a pdf users manual you could email?
Thanks, George
--- In CAD_CAM_EDM_DRO@yahoogroups.com, shawncd@... wrote:
>
> Hi George,
> I also have several stand alone DMC-730 three axis
> controllers. These can be bought for very little money
> on ebay. They are good controllers. I currently use
> Galils old software "G Code to DMC" its ok, but its
> not any where close to a comercial setup. If you like
> I can send you a copy of the software. I could also
> send you a 730 unit if you would like to play around
> with it.
> I have all of galils drivers for the 1000 series
> controllers as well as the 730 so hopefully I can get
> your software to comunicate with each.
> I'm looking forward to testing your software.
> I'll let you know how I come out.
> Shawn
Discussion Thread
geostabilizer
2006-01-30 16:42:53 UTC
dxf to gcode to Galil DMC software
geostabilizer
2006-01-30 19:38:37 UTC
Re: dxf to gcode to Galil DMC software
geostabilizer
2006-01-30 19:39:55 UTC
Re: dxf to gcode to Galil DMC software
Brad
2006-01-31 15:14:49 UTC
Re: dxf to gcode to Galil DMC software
geostabilizer
2006-02-01 13:35:00 UTC
Re: dxf to gcode to Galil DMC software
Shawncd
2006-02-01 17:37:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
Shawncd
2006-02-01 17:38:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
Shawncd
2006-02-01 17:46:19 UTC
Re: dxf to gcode to Galil DMC software
geostabilizer
2006-02-01 19:30:32 UTC
Re: dxf to gcode to Galil DMC software
shawncd@p...
2006-02-02 11:20:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
geostabilizer
2006-02-06 07:25:23 UTC
Re: dxf to gcode to Galil DMC software
shawncd@p...
2006-02-06 11:02:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
Shawncd
2006-02-07 19:29:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
geostabilizer
2006-02-08 09:57:59 UTC
Re: dxf to gcode to Galil DMC software
GutZ
2010-12-22 05:44:26 UTC
Re: dxf to gcode to Galil DMC software