Re: dxf to gcode to Galil DMC software
Posted by
geostabilizer
on 2006-02-08 09:57:59 UTC
Shawn,
Please try emailing me the pdf file.
Cheers, George
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Shawncd" <shawncd@...>
wrote:
Please try emailing me the pdf file.
Cheers, George
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Shawncd" <shawncd@...>
wrote:
>have a
> The DMC-700 pdf. is 13mb would you like this emailed or do you
> different preference before I send it?Do
> Shawn
>
>
>
>
>
> ----- Original Message -----
> From: "geostabilizer" <gmalone@...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Monday, February 06, 2006 9:22 AM
> Subject: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
>
>
> > Hi Shawn,
> > I checked galilmc.com and could not find any info on the 730
> > controller. I suspect it is not a "bus-based" type. If it is the
> > stand alone RS-232 type of interface my software should still be
> > able to communicate with it using the Windows drivers however the
> > real-time controller status may be too slow for the purpose of
> > controller the laser. I would like to know more about this card.
> > you have a pdf users manual you could email?
> >
> > Thanks, George
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, shawncd@ wrote:
> > >
> > > Hi George,
> > > I also have several stand alone DMC-730 three axis
> > > controllers. These can be bought for very little money
> > > on ebay. They are good controllers. I currently use
> > > Galils old software "G Code to DMC" its ok, but its
> > > not any where close to a comercial setup. If you like
> > > I can send you a copy of the software. I could also
> > > send you a 730 unit if you would like to play around
> > > with it.
> > > I have all of galils drivers for the 1000 series
> > > controllers as well as the 730 so hopefully I can get
> > > your software to comunicate with each.
> > > I'm looking forward to testing your software.
> > > I'll let you know how I come out.
> > > Shawn
Discussion Thread
geostabilizer
2006-01-30 16:42:53 UTC
dxf to gcode to Galil DMC software
geostabilizer
2006-01-30 19:38:37 UTC
Re: dxf to gcode to Galil DMC software
geostabilizer
2006-01-30 19:39:55 UTC
Re: dxf to gcode to Galil DMC software
Brad
2006-01-31 15:14:49 UTC
Re: dxf to gcode to Galil DMC software
geostabilizer
2006-02-01 13:35:00 UTC
Re: dxf to gcode to Galil DMC software
Shawncd
2006-02-01 17:37:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
Shawncd
2006-02-01 17:38:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
Shawncd
2006-02-01 17:46:19 UTC
Re: dxf to gcode to Galil DMC software
geostabilizer
2006-02-01 19:30:32 UTC
Re: dxf to gcode to Galil DMC software
shawncd@p...
2006-02-02 11:20:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
geostabilizer
2006-02-06 07:25:23 UTC
Re: dxf to gcode to Galil DMC software
shawncd@p...
2006-02-06 11:02:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
Shawncd
2006-02-07 19:29:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: dxf to gcode to Galil DMC software
geostabilizer
2006-02-08 09:57:59 UTC
Re: dxf to gcode to Galil DMC software
GutZ
2010-12-22 05:44:26 UTC
Re: dxf to gcode to Galil DMC software