CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Force feedback handwheels

Posted by Les Newell
on 2006-07-24 10:52:23 UTC
Hi Dave,

> One might be to put a meter that shows torque of the spindle. it
> would show one of the first stages of excess power needed from dull
> tools or tools that are not set at the proper height.

I already have a meter on the spindle. However as it has a 10hp motor
and the gearbox has a lot of drag you hardly notice the extra load of a
cut unless you are taking really heavy cuts. This beast doesn't even
notice cuts that would stall my previous lathe :-).

>
> The force feedback would, in my mind be valuable for light materials
> so you don't go plowing into things that might not like high pressures.


Good point. However I think I will forget about force feedback for the
time being. My current hand wheel design would be very easy to convert
over force feedback at a later date if I decide it is worth
investigating further.


> and hard materials, where a dull tool will drastically increase forces
> needed to cut.

The red swarf is usually a good indication ;-)

Thanks,
Les

Discussion Thread

Joe 2006-07-12 20:17:46 UTC CAD packages Jarrett & Heidi Johnson 2006-07-12 20:32:07 UTC Re: [CAD_CAM_EDM_DRO] CAD packages hannu venermo 2006-07-13 04:35:38 UTC Re: [CAD_CAM_EDM_DRO] CAD packages Ryan Johnson 2006-07-13 05:10:18 UTC RE: [CAD_CAM_EDM_DRO] CAD packages WT 2006-07-13 06:02:11 UTC Re: [CAD_CAM_EDM_DRO] CAD packages Pete Brown (YahooGroups) 2006-07-13 16:12:37 UTC RE: [CAD_CAM_EDM_DRO] CAD packages mikehenryil 2006-07-13 18:59:34 UTC Re: CAD packages Harko Schwartz 2006-07-14 05:53:40 UTC Re: [CAD_CAM_EDM_DRO] CAD packages Luke1027 2006-07-14 07:49:48 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD packages Luke1027 2006-07-14 08:52:44 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD packages Seiman H 2006-07-23 07:44:57 UTC Speed reducer or GEAR BOX FOR NEMA23, 34 gawnca 2006-07-23 14:17:43 UTC Re: CAD packages gawnca 2006-07-23 17:59:46 UTC Re: CAD packages mechatronics international 2006-07-24 02:03:36 UTC CAD packages Graham Stabler 2006-07-24 04:14:12 UTC Re: CAD packages Pete Brown (YahooGroups) 2006-07-24 04:49:45 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD packages Ryan Johnson 2006-07-24 06:06:40 UTC RE: [CAD_CAM_EDM_DRO] Re: CAD packages Robert Colin Campbell 2006-07-24 06:41:55 UTC Re: [CAD_CAM_EDM_DRO] Re: CAD packages Les Newell 2006-07-24 06:54:35 UTC Force feedback handwheels Paul Kelly 2006-07-24 07:06:05 UTC RE: [CAD_CAM_EDM_DRO] Force feedback handwheels turbulatordude 2006-07-24 07:55:44 UTC Re: Force feedback handwheels lcdpublishing 2006-07-24 08:23:01 UTC Re: Force feedback handwheels Les Newell 2006-07-24 10:38:38 UTC Re: [CAD_CAM_EDM_DRO] Force feedback handwheels Les Newell 2006-07-24 10:52:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Force feedback handwheels Dennis Schmitz 2006-07-24 11:47:30 UTC Re: [CAD_CAM_EDM_DRO] Force feedback handwheels Graham Stabler 2006-07-24 13:38:37 UTC Re: Force feedback handwheels Graham Stabler 2006-07-24 13:38:37 UTC Re: CAD packages