CAD CAM EDM DRO - Yahoo Group Archive

Re: milling circuit boards

on 2006-10-05 19:10:02 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "wdavis364" <wdavis@...> wrote:
>
> Shopping around for a router, Some router have 1/4 collets and some
> have 1/4 collets and 1/8 collets. Not knowing much about this, what
> size collet will I would most likely to be using in milling circuit
> boards. Will 1/4 collets handle the very small size drill bits(1/32)?
> Thanks for any advice on this.
> bill

the standard drill diameter for PCB work is 1/8" dia. Therefore, to
answer your quesiton, 1/8"

You can buy drill bits on E-bay for about 50 cents each, in lots of
25. Go for the guys who will tell you up-front what diameter drills
you will get.

I bougth a cheap set and 45 pieces were 13 thou or less. Totally
unusable for my needs.

Dave


>

Discussion Thread

wdavis364 2006-10-05 17:28:00 UTC milling circuit boards Dennis Schmitz 2006-10-05 18:42:40 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards turbulatordude 2006-10-05 19:10:02 UTC Re: milling circuit boards Paul Kelly 2006-10-05 19:20:25 UTC RE: [CAD_CAM_EDM_DRO] milling circuit boards R Rogers 2006-10-05 19:39:18 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards BRIAN FOLEY 2006-10-05 19:40:29 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards Bill Davis 2006-10-05 20:45:16 UTC Re: [CAD_CAM_EDM_DRO] Re: milling circuit boards paultitchener 2006-10-05 22:02:58 UTC Re: milling circuit boards turbulatordude 2006-10-06 07:06:21 UTC Re: milling circuit boards R Rogers 2006-10-06 07:28:25 UTC Re: [CAD_CAM_EDM_DRO] Re: milling circuit boards KM6VV 2006-10-06 07:53:27 UTC RE: [CAD_CAM_EDM_DRO] milling circuit boards Tony Jeffree 2006-10-06 07:57:25 UTC Re: [CAD_CAM_EDM_DRO] Re: milling circuit boards KM6VV 2006-10-06 08:07:57 UTC RE: [CAD_CAM_EDM_DRO] milling circuit boards Jack Coats 2006-10-06 08:09:42 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards Bill Davis 2006-10-06 08:10:40 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards Jack Coats 2006-10-06 08:16:50 UTC Re: [CAD_CAM_EDM_DRO] Re: milling circuit boards Tony Jeffree 2006-10-06 08:18:23 UTC RE: [CAD_CAM_EDM_DRO] milling circuit boards KM6VV 2006-10-06 08:33:16 UTC RE: [CAD_CAM_EDM_DRO] milling circuit boards Dennis Schmitz 2006-10-06 08:35:32 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards KM6VV 2006-10-06 08:41:46 UTC RE: [CAD_CAM_EDM_DRO] Re: milling circuit boards Tony Jeffree 2006-10-06 08:56:57 UTC RE: [CAD_CAM_EDM_DRO] milling circuit boards turbulatordude 2006-10-06 09:22:24 UTC Re: milling circuit boards Jack Coats 2006-10-06 09:30:54 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards caudlet 2006-10-06 09:42:26 UTC Re: milling circuit boards Richard 2006-10-06 09:49:46 UTC Re: milling circuit boards caudlet 2006-10-06 10:02:28 UTC Re: milling circuit boards [source for collets and bits] paultitchener 2006-10-06 10:17:35 UTC Re: milling circuit boards [source for collets and bits] Andrew Werby 2006-10-06 11:35:11 UTC Re: milling circuit boards Bill Davis 2006-10-06 11:49:59 UTC Re: [CAD_CAM_EDM_DRO] Re: milling circuit boards [source for collets and bits] Jack Coats 2006-10-06 13:06:43 UTC Re: [CAD_CAM_EDM_DRO] Re: milling circuit boards [source for collets and bits] KM6VV 2006-10-06 14:39:38 UTC RE: [CAD_CAM_EDM_DRO] milling circuit boards Mark Vaughan 2006-10-07 05:58:22 UTC RE: [CAD_CAM_EDM_DRO] milling circuit boards William Perun Sr 2006-10-07 08:25:57 UTC Re: milling circuit boards deepcavity 2006-10-07 18:41:47 UTC Re: [CAD_CAM_EDM_DRO] Re: milling circuit boards deepcavity 2006-10-07 19:17:39 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards Bill Davis 2006-10-07 20:46:34 UTC Re: [CAD_CAM_EDM_DRO] milling circuit boards optics22000 2006-10-08 12:39:04 UTC KDN high speed spindle, was Re: milling circuit boards Steve Blackmore 2006-10-08 18:06:52 UTC Re: [CAD_CAM_EDM_DRO] KDN high speed spindle, was Re: milling circuit boards Chris Horne 2006-10-09 11:29:29 UTC KDN high speed spindle, was Re: milling circuit boards