Re: ball screw preferences
Posted by
ballendo
on 2007-03-12 16:12:29 UTC
>In CCED, Steve Blackmore <steve@...> wrote:Steve,
>Or you buy antibacklash nuts - cheaper than 2 nuts.
>http://www.marchantdice.com/linear/backlash.pdf
>
>BTW - over 300 lines of excessive quote removed !
Great link, Thank you. Also appreciate the reminder about "trimming"
posts. My bad.
Ballendo
P.S. Have you used these ballnuts? They look like high end units.
Didn't notice pricing in the PDF, but only a quick look so far...
Discussion Thread
Billy Stringfellow
2007-03-08 18:05:06 UTC
ball screw preferences
Aubrey Laughlin
2007-03-08 20:21:14 UTC
Re: [CAD_CAM_EDM_DRO] ball screw preferences
Mark Vaughan
2007-03-09 08:39:44 UTC
RE: [CAD_CAM_EDM_DRO] ball screw preferences
wjstape
2007-03-09 09:54:22 UTC
Re: ball screw preferences
R Wink
2007-03-09 12:34:24 UTC
RE: [CAD_CAM_EDM_DRO] ball screw preferences
Mark Vaughan
2007-03-10 10:00:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw preferences
ballendo
2007-03-11 03:21:04 UTC
Re: ball screw preferences
Mark Vaughan
2007-03-11 09:24:00 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw preferences
ballendo
2007-03-11 22:22:21 UTC
Re: ball screw preferences
Steve Blackmore
2007-03-12 01:27:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw preferences
Mark Vaughan
2007-03-12 01:28:03 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw preferences
lcdpublishing
2007-03-12 14:39:09 UTC
Re: ball screw preferences
ballendo
2007-03-12 16:12:29 UTC
Re: ball screw preferences
ballendo
2007-03-12 16:39:06 UTC
Re: ball screw preferences
ballendo
2007-03-12 17:09:04 UTC
Re: ball screw preferences
Steve Blackmore
2007-03-13 01:30:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw preferences
Mark Vaughan
2007-03-13 01:41:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw preferences
ballendo
2007-03-13 02:11:07 UTC
Re: ball screw preferences
ballendo
2007-03-13 02:17:24 UTC
Re: ball screw preferences
Mark Vaughan
2007-03-13 02:51:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: ball screw preferences
R Rogers
2007-03-13 07:57:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw preferences
ballendo
2007-03-13 09:11:22 UTC
Re: ball screw preferences
R Rogers
2007-03-13 13:00:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw preferences
Steve Blackmore
2007-03-13 14:40:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: ball screw preferences