Re: [CAD_CAM_EDM_DRO] Re: Adding a Tail shaft to servo's with no tail shaft
Posted by
David G. LeVine
on 2007-04-29 11:22:05 UTC
At 02:27 AM 4/29/2007, you wrote:
any drive (as in motor to leadscrew) backlash in it. Using a DRO as
an encoder is not all bad...
David G. LeVine
Nashua, NH 03060
>One hobbyist level case is the leadscrew mouting of the encoders inJust to point out, an encoder mounted to the leadscrew will not have
>Aaron Moss's Industrialhobbies.com benchmill conversions.
any drive (as in motor to leadscrew) backlash in it. Using a DRO as
an encoder is not all bad...
David G. LeVine
Nashua, NH 03060
Discussion Thread
jerryflyguy
2007-04-26 14:08:54 UTC
Adding a Tail shaft to servo's with no tail shaft
Mark Vaughan
2007-04-26 14:50:21 UTC
RE: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
H & J Johnson
2007-04-26 14:58:45 UTC
Re: RE: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
Wayne Weedon
2007-04-26 15:31:23 UTC
Re: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
H & J Johnson
2007-04-26 15:39:25 UTC
Re: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
turbulatordude
2007-04-26 16:07:32 UTC
Re: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
Mark Vaughan
2007-04-26 16:36:46 UTC
RE: RE: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
aclausing2003
2007-04-26 17:04:11 UTC
Re: Adding a Tail shaft to servo's with no tail shaft
Vince Endter
2007-04-26 19:52:58 UTC
Re: Adding a Tail shaft to servo's with no tail shaft
vrsculptor
2007-04-27 19:59:27 UTC
Re: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
Jarrett & Heidi Johnson
2007-04-27 20:30:12 UTC
Re: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
BRIAN FOLEY
2007-04-27 20:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
Tony Smith
2007-04-27 22:52:08 UTC
RE: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
Mark Vaughan
2007-04-28 00:15:16 UTC
RE: [CAD_CAM_EDM_DRO] Adding a Tail shaft to servo's with no tail shaft
vrsculptor
2007-04-28 07:08:54 UTC
Re: Adding a Tail shaft to servo's with no tail shaft
Tony Smith
2007-04-28 08:45:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: Adding a Tail shaft to servo's with no tail shaft
Jarrett & Heidi Johnson
2007-04-28 15:58:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Adding a Tail shaft to servo's with no tail shaft
ballendo
2007-04-28 23:28:53 UTC
Re: Adding a Tail shaft to servo's with no tail shaft
David G. LeVine
2007-04-29 11:22:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Adding a Tail shaft to servo's with no tail shaft
Steve Blackmore
2007-04-29 17:18:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Adding a Tail shaft to servo's with no tail shaft