Re: [CAD_CAM_EDM_DRO] rant
Posted by
Steve Blackmore
on 2008-04-06 16:59:36 UTC
On Sun, 6 Apr 2008 15:32:17 -0400, you wrote:
since Independence ;)
Steve Blackmore
--
>Once in US history, a state legislator introduced a bill to define pi as 3.0 rather than the messy 3.14159+. Why stop with theIf your a Yank - your recommended official measurement has been metric
>meter? Are you suggesting we change the inch or the meter?
since Independence ;)
Steve Blackmore
--
Discussion Thread
Peter Reilley
2008-04-06 07:02:46 UTC
Re: [CAD_CAM_EDM_DRO] rant
stan
2008-04-06 07:51:17 UTC
Ref: rant
Peter Reilley
2008-04-06 08:03:07 UTC
Re: [CAD_CAM_EDM_DRO] Ref: rant
Tony Jeffree
2008-04-06 09:23:56 UTC
Re: [CAD_CAM_EDM_DRO] Ref: rant
stan
2008-04-06 09:36:38 UTC
Ref: rant
Jon Elson
2008-04-06 09:47:27 UTC
Re: [CAD_CAM_EDM_DRO] rant
stan
2008-04-06 10:27:13 UTC
Ref: rant
Peter Reilley
2008-04-06 10:46:01 UTC
Re: [CAD_CAM_EDM_DRO] Ref: rant
R.L. Wurdack
2008-04-06 10:51:29 UTC
Re: [CAD_CAM_EDM_DRO] rant
stan
2008-04-06 10:52:38 UTC
Alternatives to ballscrews
stan
2008-04-06 11:02:02 UTC
Ref: rant
turbulatordude
2008-04-06 11:09:26 UTC
Re: rant
R.L. Wurdack
2008-04-06 11:33:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: rant
stan
2008-04-06 11:34:51 UTC
Ref: rant
stan
2008-04-06 12:05:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: rant
Jim Peck Stamping
2008-04-06 12:32:54 UTC
rant
Jim Peck Stamping
2008-04-06 13:00:51 UTC
rant
R.L. Wurdack
2008-04-06 13:34:40 UTC
Re: [CAD_CAM_EDM_DRO] rant
Peter Reilley
2008-04-06 15:13:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: rant
Steve Blackmore
2008-04-06 16:59:36 UTC
Re: [CAD_CAM_EDM_DRO] rant
stan
2008-04-06 17:08:12 UTC
Re: [CAD_CAM_EDM_DRO] rant
Matthew Tinker
2008-04-06 17:16:38 UTC
Re: [CAD_CAM_EDM_DRO] rant
Jon Elson
2008-04-06 17:35:54 UTC
Re: [CAD_CAM_EDM_DRO] Ref: rant
stan
2008-04-06 17:44:04 UTC
Ref: rant
wanliker@a...
2008-04-06 17:53:03 UTC
Ref: rant
Jim Register
2008-04-06 17:57:55 UTC
Laser Metrology (was Re: rant)
stan
2008-04-06 18:31:33 UTC
Re: [CAD_CAM_EDM_DRO] Laser Metrology (was Re: rant)
stan
2008-04-06 18:55:02 UTC
Ref: Laser Metrology
Brian Foley
2008-04-06 20:52:42 UTC
Re: [CAD_CAM_EDM_DRO] Ref: rant
Jim Peck Stamping
2008-04-07 04:00:27 UTC
rant
caudlet
2008-04-07 06:47:18 UTC
Re: Ref: rant [Off Topic]
Matthew Tinker
2008-04-07 06:49:42 UTC
Re: [CAD_CAM_EDM_DRO] Ref: rant
Tony Smith
2008-04-07 07:45:14 UTC
RE: [CAD_CAM_EDM_DRO] rant
dickw@n...
2008-04-07 13:16:10 UTC
Re: [CAD_CAM_EDM_DRO] Ref: Laser Metrology
stan
2008-04-07 14:16:07 UTC
Ref: Laser Metrology
Graham Stabler
2008-04-07 15:28:14 UTC
Re: Ref: Laser Metrology
R.L. Wurdack
2008-04-07 19:40:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ref: Laser Metrology
vrsculptor
2008-04-07 20:20:05 UTC
Re: Ref: Laser Metrology
Peter Reilley
2008-04-07 20:21:26 UTC
Re: [CAD_CAM_EDM_DRO] Ref: Laser Metrology