Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Posted by
Michael Fagan
on 2008-08-20 23:07:29 UTC
If you have a good lathe and time, you can make a taper-lock just as
good as any commercial one, particularly if you have the original to
measure from. I made a set of serpentine belt pullies out of 7075
aluminum, and I used commercial hubs and machined the mating section
right into the pulley. On another job, I used commercial timing belt
pullies with 303 stainless hubs I made.
good as any commercial one, particularly if you have the original to
measure from. I made a set of serpentine belt pullies out of 7075
aluminum, and I used commercial hubs and machined the mating section
right into the pulley. On another job, I used commercial timing belt
pullies with 303 stainless hubs I made.
On Wed, Aug 20, 2008 at 9:16 AM, Jon Elson <elson@...> wrote:
> Leslie Newell wrote:
>> If I remember correctly the pulleys use taper lock fixing. You should be
>> able to get a new taper lock insert with the correct bore.
> Yes, but they are VERY expensive. They could cost $45 to 60
> each, just for the hub part, and you have to make sure you get
> one from the same maker and series.
>
> Jon
>
Discussion Thread
smirob1
2008-08-19 17:10:19 UTC
Preparing for a Series 1 Retrofit
Jon Elson
2008-08-19 18:00:45 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
shawn c
2008-08-19 20:51:41 UTC
RE: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
jbrennan3@a...
2008-08-19 20:59:09 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Leslie Newell
2008-08-20 00:45:02 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Marv Frankel
2008-08-20 07:55:28 UTC
Re: Preparing for a Series 1 Retrofit
Jon Elson
2008-08-20 09:21:45 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Leslie Newell
2008-08-20 09:58:57 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Jon Elson
2008-08-20 18:47:12 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Michael Fagan
2008-08-20 23:07:29 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Leslie Newell
2008-08-21 00:28:01 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Michael Fagan
2008-08-21 00:29:41 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Leslie Newell
2008-08-21 01:00:41 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Michael Fagan
2008-08-21 01:08:34 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
556RECON
2008-08-21 12:24:48 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Roger Blair
2008-08-21 16:17:34 UTC
RE: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
smirob1
2008-08-21 23:46:01 UTC
Re: Preparing for a Series 1 Retrofit
Mark Bingham
2008-08-23 04:49:33 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Jon Elson
2008-08-23 09:58:04 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
556RECON
2008-08-23 11:24:55 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Mark Bingham
2008-08-23 16:37:57 UTC
Re: Preparing for a Series 1 Retrofit
Jon Elson
2008-08-23 19:10:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Preparing for a Series 1 Retrofit