Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Posted by
Leslie Newell
on 2008-08-21 00:28:01 UTC
As you say, it shouldn't be difficult. As long as you turn the OD and
bore without taking the part out of the chuck it should be very concentric.
Les
Jon Elson wrote:
bore without taking the part out of the chuck it should be very concentric.
Les
Jon Elson wrote:
> No question. But, I think you can turn a sleeve and then slot
> it, and line the slots up with the ones in the taper-lock hub,
> and have a very tight and concentric adaptor that preserves all
> the good qualities of the taper lock.
>
> Jon
>
Discussion Thread
smirob1
2008-08-19 17:10:19 UTC
Preparing for a Series 1 Retrofit
Jon Elson
2008-08-19 18:00:45 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
shawn c
2008-08-19 20:51:41 UTC
RE: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
jbrennan3@a...
2008-08-19 20:59:09 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Leslie Newell
2008-08-20 00:45:02 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Marv Frankel
2008-08-20 07:55:28 UTC
Re: Preparing for a Series 1 Retrofit
Jon Elson
2008-08-20 09:21:45 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Leslie Newell
2008-08-20 09:58:57 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Jon Elson
2008-08-20 18:47:12 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Michael Fagan
2008-08-20 23:07:29 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Leslie Newell
2008-08-21 00:28:01 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Michael Fagan
2008-08-21 00:29:41 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Leslie Newell
2008-08-21 01:00:41 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Michael Fagan
2008-08-21 01:08:34 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
556RECON
2008-08-21 12:24:48 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Roger Blair
2008-08-21 16:17:34 UTC
RE: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
smirob1
2008-08-21 23:46:01 UTC
Re: Preparing for a Series 1 Retrofit
Mark Bingham
2008-08-23 04:49:33 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Jon Elson
2008-08-23 09:58:04 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
556RECON
2008-08-23 11:24:55 UTC
Re: [CAD_CAM_EDM_DRO] Preparing for a Series 1 Retrofit
Mark Bingham
2008-08-23 16:37:57 UTC
Re: Preparing for a Series 1 Retrofit
Jon Elson
2008-08-23 19:10:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Preparing for a Series 1 Retrofit