Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Posted by
Roland Jollivet
on 2010-09-12 08:57:07 UTC
If you drill a small hole through the centre of the back of the rear cap,
maybe 1/4in, you'll find that the shaft has been centre drilled for
manufacture. With a small bracket, thrust bearing and a pointed little
shaft, you can press against it. You have now simply extended the shaft out
the rear, and you can attach a plastic disc or whatever onto it to pickup
the speed.
Obviously remove the cap first to see if there are any wires there.
Roland
maybe 1/4in, you'll find that the shaft has been centre drilled for
manufacture. With a small bracket, thrust bearing and a pointed little
shaft, you can press against it. You have now simply extended the shaft out
the rear, and you can attach a plastic disc or whatever onto it to pickup
the speed.
Obviously remove the cap first to see if there are any wires there.
Roland
On 12 September 2010 07:34, David G. LeVine <dlevine@...> wrote:
>
>
> On 09/11/2010 11:52 PM, Jon Elson wrote:
> > Gaston Gagnon wrote:
> >
> >> Ooops! I confused things here. Some of these sensors (ATS616LSG) are
> >> spec as max Operating freq of 10 kHz and others (ATS667LSG) as Operating
> >> Speed of 12000 rpm.
> >>
> >>
> > Yes, that 12000 RPM spec is with their 40-tooth reference gear, I think.
> >
> > Jon
> >
>
> 12,000 * 40 is 480,000 PPM / 60 min/sec is 8,000 Hz. 8,000 * 60 / 6 is
> 80,000 RPM...
>
>
>
[Non-text portions of this message have been removed]
Discussion Thread
danmauch
2010-09-06 09:56:47 UTC
Machine mounted Tachometer with Surface Meter Per minuteThis
Gaston Gagnon
2010-09-09 11:01:30 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Dan Mauch
2010-09-09 12:34:04 UTC
RE: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Gaston Gagnon
2010-09-09 13:20:31 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Tony Smith
2010-09-09 18:00:43 UTC
RE: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Will Holding
2010-09-10 01:28:08 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Gaston Gagnon
2010-09-10 08:18:16 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
556RECON
2010-09-10 09:50:15 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-10 19:09:44 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Gaston Gagnon
2010-09-10 22:22:59 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Tony Smith
2010-09-10 23:05:05 UTC
RE: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Tony Smith
2010-09-11 00:06:05 UTC
RE: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Dave Halliday
2010-09-11 00:26:55 UTC
RE: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Michael Fagan
2010-09-11 00:56:12 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Tony Smith
2010-09-11 01:08:19 UTC
RE: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Danny Miller
2010-09-11 01:57:11 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Danny Miller
2010-09-11 02:01:34 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Will Holding
2010-09-11 03:59:31 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-11 08:47:13 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-11 09:01:52 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-11 09:04:39 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-11 09:08:12 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-11 09:13:49 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Jon Elson
2010-09-11 09:48:12 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Tony Smith
2010-09-11 09:50:22 UTC
RE: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Jon Elson
2010-09-11 09:56:34 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Gaston Gagnon
2010-09-11 10:00:49 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Gaston Gagnon
2010-09-11 10:13:08 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Will Holding
2010-09-11 10:48:01 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-11 10:48:31 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-11 10:49:24 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Will Holding
2010-09-11 13:13:21 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Jon Elson
2010-09-11 20:52:09 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-11 22:34:58 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Roland Jollivet
2010-09-12 08:57:07 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Gaston Gagnon
2010-09-12 09:11:31 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Jon Elson
2010-09-12 10:25:19 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
David G. LeVine
2010-09-12 11:15:15 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Will Holding
2010-09-12 16:37:22 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer with Surface Meter Per minuteThis
Gaston Gagnon
2010-10-11 17:12:46 UTC
Re: [CAD_CAM_EDM_DRO] Machine mounted Tachometer UPDATE