[CAD_CAM_EDM_DRO] single axis control
Posted by
Roland Jollivet
on 2012-10-24 04:58:21 UTC
Also, the code for CncPro is freely available, so you could, if it's your
forte', edit the code (Borland C++) to put in any comms or tailoring
required.
Regards
Roland
forte', edit the code (Borland C++) to put in any comms or tailoring
required.
Regards
Roland
On 23 October 2012 16:57, Andy Wander <ohawiseguyeh@...> wrote:
> **
>
>
> So what if it's overkill? Get a cheap PC, install Mach3, and away you go.
>
> Andy Wander
>
>
> _____
>
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of scyvt
> Sent: Tuesday, October 23, 2012 10:46 AM
>
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] single axis control
>
> Hello group
>
> I have 2 applications for single axis stepper control: one moving a cut-off
> stop, and the other moving a table holding a part being drilled, both in
> pre-determined increments, and with the need to store programs for numerous
> parts. Although either Mach or EMC could do this, it seems like cutting
> butter with a chainsaw. However, there doesn't seem to be much in the way
> of
> single axis controllers on the market, and I don't have the knowledge to
> brew up one with a microcontroller. Perhaps this could be an application
> for
> a PLC, but there seems to be a learning curve to program one (not G-code).
> Any suggestions?
>
> TIA
>
> Steve
>
> [Non-text portions of this message have been removed]
>
>
>
[Non-text portions of this message have been removed]
Discussion Thread
scyvt
2012-10-23 07:45:36 UTC
single axis control
Andy Wander
2012-10-23 07:57:29 UTC
RE: [CAD_CAM_EDM_DRO] single axis control
Roland Jollivet
2012-10-23 08:08:04 UTC
[CAD_CAM_EDM_DRO] single axis control
John Dammeyer
2012-10-23 09:21:12 UTC
RE: [CAD_CAM_EDM_DRO] single axis control
Roland Jollivet
2012-10-23 09:36:41 UTC
[CAD_CAM_EDM_DRO] single axis control
scyvt
2012-10-23 10:15:14 UTC
Re: single axis control
John Murphy
2012-10-23 11:03:29 UTC
Re: [CAD_CAM_EDM_DRO] single axis control
Rjreese29
2012-10-23 11:04:16 UTC
Re: [CAD_CAM_EDM_DRO] single axis control
Jeffrey Birt
2012-10-23 11:05:07 UTC
RE: [CAD_CAM_EDM_DRO] single axis control
John Dammeyer
2012-10-23 11:12:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: single axis control
jeremy youngs
2012-10-23 13:45:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: single axis control
jeremy youngs
2012-10-23 14:56:53 UTC
Re: [CAD_CAM_EDM_DRO] single axis control
David G. LeVine
2012-10-23 20:20:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: single axis control
Roland Jollivet
2012-10-24 04:58:21 UTC
[CAD_CAM_EDM_DRO] single axis control
jeremy youngs
2012-10-24 14:36:47 UTC
Re: [CAD_CAM_EDM_DRO] single axis control