CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Single phase mains

Posted by Bill Darby
on 2000-09-23 10:37:39 UTC
Jerry Kimberlin wrote:

>
> Bill Darby wrote:
>
> > These single to three phase variable frequency control units do not seem to be available in the five horse variety
>
> Hitachi make them - 1/2 to 10 hp, 230v or 460v input. A 5 hp
> 230v single phase input, 3-P output is $400.

I looked but could not see any. Could you give me the number for the unit. The closest I came was for the sj100-037lfu but it was 3
phase input.

Thanks Bill Darby

>
>
> Check Automation Direct (under drives) to see characteristics.
> There are other suppliers as well.
>
> http://store.automationdirect.com/cgi-bin/ncommerce3/ExecMacro/plcdirect/homeframe.d2w/report
>
> JerryK
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager

Discussion Thread

Bill Darby 2000-09-23 09:45:19 UTC Single phase mains Jerry Kimberlin 2000-09-23 09:56:09 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains Bill Darby 2000-09-23 10:37:39 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains Jerry Kimberlin 2000-09-23 18:00:10 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains Darrell 2000-09-23 18:38:40 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains Jon Elson 2000-09-23 22:18:10 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains Bill Darby 2000-09-24 05:48:27 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains machines@n... 2000-09-24 07:54:33 UTC Re: Single phase mains dougrasmussen@c... 2000-09-24 18:02:21 UTC Re: Single phase mains Bill Darby 2000-09-28 05:36:48 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains machines@n... 2000-09-28 05:48:29 UTC Re: Single phase mains Jerry Kimberlin 2000-09-28 08:35:08 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains paul@a... 2000-09-28 09:05:59 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains Jon Elson 2000-09-28 20:06:49 UTC Re: [CAD_CAM_EDM_DRO] Single phase mains